0002037: [Serial Driver/Interface] Baud rate of debug port can not be changed 0002036: [SD/MMC] SD Card is always write-protected 0002035: [Touch driver] mach-picocom4.c won't compile if s3c2410_touch is disabled 0002034: [Touch driver] Buttons sometimes need to be touched twice on Focaltech FT5x06 to be recognized

0002032: [Display] Add generic LCD configuration 0002031: [Kernel] Add and use F&S Tux logo (Tux holding NetDCU logo) 0002033: [Touch driver] Buttons are only recognized after a second touch 0002030: [Serial Driver/Interface] Add correct Pull-ups and Pull-downs to UART lines 0001767: [SD/MMC] Some SD cards report timeouts 0001707: [SPI] Sending more than 22 bytes data not working w/ speed < 1MHz 0001766: [Touch driver] Use improved driver from S5PV210 0001611: [Display] Add PWM backlight control for VEEK 0001610: [Audio] Noisy sound when recording 0001609: [Touch driver] FT5X06: Add SYSFS support to configure parameters

0001101: [CAN] GPIO auf SPI & CAN

0005280: [Display] [i.MX6] Weston does not work correctly when using chvt with use-g2d in weston.ini 0006232: [Buildroot] Update fsimx6 boards to Buildroot 2024.01

0006111: [Buildroot] Update fsimx6sx boards to Buildroot 2024.01

0006033: [Buildroot] Update fsimx6ul boards to Buildroot 2023.02

0006008: [Buildroot] Add F&S Kernel and U-Boot versioning 0006009: [Buildroot] Add F&S psplash bootscreen 0006007: [Buildroot] Update IMX specific packages to NXP Yocto version lf-5.15.71-2.2.1 0006006: [Buildroot] Update to Buildroot 2023.02.6

0005571: [General] Improve fsimx8mm install script 0005570: [General] Add picocoremx8mmr2 device trees

0005170: [Buildroot] Add error handling for the install script with eMMC 0005329: [Buildroot] Add TSC2004 Touchscreen default calibration 0005330: [Buildroot] Add wlan regulatory.db to imx6/7 defonfigs 0005268: [Buildroot] Bump busybox from 1.33.0 to 1.33.2 0005327: [Buildroot] Update Buildroot to buildroot-2021.02.10 0005169: [Buildroot] Improve support for current buildroot version for platform fsimx7ulp 0005168: [Buildroot] Improve support for current buildroot version for platform fsimx6sx/fsimx6ul

0005171: [Buildroot] Add support for board efusA9r2

0005114: [Buildroot] Update history file to buildroot-2021.02.2-fsimx6-B2021.10.1

0005113: [Buildroot] Update history file to buildroot-2021.02.2-fsimx6-B2021.10 0005112: [Buildroot] Add bulding of install.scr script with buildroot 0005111: [Buildroot] Fix imx6 alsa sound 0005110: [Buildroot] Add default touchscreen calibration SX8654 0005109: [Buildroot] Add experimental fsimx6 etnaviv defconfig 0005108: [Buildroot] Add building of emmc-sysimg for fsimx6 0005107: [Buildroot] Add fsimx6 Uboot building with Buildroot 0005106: [Buildroot] Add g2d support to weston 0005105: [Buildroot] Add xwayland defconfig 0005104: [Buildroot] Improve imx-gpu arm32 packages 0005103: [Buildroot] Improve imx6 defconfigs 0005102: [Buildroot] Add BR2_PACKAGE_LINUX_FIRMWARE_MWIFIEX_PCIEUSB8997 for fsimx6* configs 0005101: [Buildroot] Improve fsimx6sx* defconfigs to support new device tree vand3 0005100: [Buildroot] Improve fsimx6ul* defconfigs to support new device tree gar3

0005256: [Buildroot] Improve support for fsimx6ul* defconfigs

0005058: [Buildroot] Merge Original buildroot-2020.011 0005099: [Buildroot] Update history file to buildroot-2021.02.2-fsimx8mm-B2021.06 0005098: [Buildroot] Fixup History File 0005097: [Buildroot] Improve sysimg (sdcard image) generation 0005096: [Buildroot] Improve fsimx8mm defconfigs 0005095: [Buildroot] Fix imx-gstreamer package 0005094: [Buildroot] Fix old hashes 0005093: [Buildroot] Update bluez_utils package 0005092: [Buildroot] Merge Original buildroot-2021.02.2 0005091: [Buildroot] Merge Original buildroot-2021.02.1 0005090: [Buildroot] Update imx specific packages 0005089: [Buildroot] Update fsimx8mm_wayland_defconfig 0005088: [Buildroot] Merge Original buildroot-2021.02 0005087: [Buildroot] Update to libopenssl-1.1.1k 0005086: [Buildroot] fsimx6{sx,ul}_min_defconfig: Correctly load SDMA firmware 0005085: [Buildroot] Fix: busybox 1.33 0005084: [Buildroot] Change: Several files that make the previous features available 0005082: [Buildroot] Add: preinit.sh 0005081: [Buildroot] Change: system.conf for rauc 0005080: [Buildroot] Add: Support for automatic update via usb drive or sd card 0005078: [Buildroot] Change: Config 0005079: [Buildroot] Add: board/f+s/common/rauc 0005077: [Buildroot] Remove: postinstall.sh 0005076: [Buildroot] Change: Path of default certificate changed 0005074: [Buildroot] Remove: S51rauc 0005073: [Buildroot] Change: Add emmc fallback support fw_env.conf.mmc 0005072: [Buildroot] Change: Increase partition number of data partition (emmc) 0005071: [Buildroot] Change: Extend demo application with startup script 0005070: [Buildroot] Extend: dynamic_mounting.py 0005069: [Buildroot] RAUC Update to 1.5 0005068: [Buildroot] Fix RAUC squashfs mounting 0005067: [Buildroot] Fixes for FS-Update 0005066: [Buildroot] Add FS-Updater for application and rootfs 0005065: [Buildroot] Fix cpio-rootfs generation 0005064: [Buildroot] Fix padding of lpddr4 ram trainigs binaries 0005063: [Buildroot] Improve fsimx8mm weston backend 0005062: [Buildroot] Improve imx8 image generation 0005061: [Buildroot] Update fsimx8mm defconfigs and busybox 0005060: [Buildroot] Update arm trusted firmware 0005059: [Buildroot] Update imx specific packages 0005057: [Buildroot] Merge Original buildroot-2020.08 0005039: [Buildroot] Merge Original buildroot-2020.05 0005038: [Buildroot] Merge buildroot-2020.02 0005037: [Buildroot] Merge Original buildroot-2019.11 0005036: [Buildroot] Merge Original buildroot-2019.08 0005035: [Buildroot] Folder bug fix for FS Updater FSIMX8MM 0005034: [Buildroot] Add FS Updater Solution scripts for FSIMX8MM architecture 0005033: [Buildroot] Add FS Updater package 0005032: [Buildroot] Latest Buildroot version of rauc 0005031: [Buildroot] Add packages and utillity for python-azure-iot-device

0004976: [Buildroot] Move entry to create install script for fsimx8mm 0004975: [Buildroot] Enable 2D support for 64-bit architecture 0004974: [Buildroot] Set PKG_CONFIG_SYSROOT_DIR to the build process 0004973: [Buildroot] Enable FW images for iMX8MM plattform 0004972: [Buildroot] Add config entries for iMX8MQ and iMX8MM 0004971: [Buildroot] Bump imx-vpu-hantro to 1.14 0004970: [Buildroot] Improve libdrm settings 0004969: [Buildroot] Add install script for fsimx8mm 0004968: [Buildroot] Bump mkimage to imx_4.14.98_2.3.0 0004967: [Buildroot] Bump uuc for ramfs default configuration 0004966: [Buildroot] Bump kobs-ng to support iMX8M(M,N) 0004965: [Buildroot] Add udev rules to create touchscreen device 0004964: [Buildroot] Add minimal configuration for fsim8mm with ramfs 0004963: [Buildroot] Add configurations to build fsimx8mm with mmc support 0004962: [Buildroot] Add minimal configuration for fsimx8mm 0004961: [Buildroot] Improve fsimx8mm support 0004377: [Buildroot] Add support for fsimx8mm

0004380: [General] [i.MX6UL] Create PicoCOMA7 release

0004395: [General] Create PicoCoreMX6UL release to support eMMC as boot device

0004395: [General] Create PicoCoreMX6UL release to support eMMC as boot device

0004380: [General] [i.MX6UL] Create PicoCOMA7 release

0004153: [Buildroot] [i.MX7ULP] Add support for fsimx7ulp_qt5_weston_defconfig 0004154: [Buildroot] Add default weston.ini file

0004061: [Buildroot] Replace gstreamer package with imx-gstreamer package 0003952: [Buildroot] Add support for MWIFIEX_SDSD8997_WLAN/BT 0003951: [Buildroot] FSIMX7ULP: Check if xserver can be used with current version

0003925: [Buildroot] Add support for firmware Marvell 88W8997 0003785: [Buildroot] Update Buildroot to 2018.11 0003784: [Buildroot] Update Buildroot to 2018.08 0003788: [Buildroot] Update to newest NXP kernel 4.9.x 0003791: [Buildroot] Add support for Sterling WLAN chip 0003790: [Buildroot] tslib causes X-Server to crash 0003789: [Buildroot] F&S standard Qt5 rootfs is huge and does not fit in NAND 0003776: [Buildroot] Update Buildroot to 2016.08 0003783: [Buildroot] Update Buildroot to 2018.05 0003782: [Buildroot] Update Buildroot to 2018.02 0003781: [Buildroot] Update Buildroot to 2017.11 0003780: [Buildroot] Update Buildroot to 2017.08 0003779: [Buildroot] Update Buildroot to 2017.05 0003778: [Buildroot] Update Buildroot to 2017.02 0003777: [Buildroot] Update Buildroot to 2016.11

0003775: [Buildroot] Add support for Silex QCA9377 WLAN/Bluetooth to Buildroot

0003765: [Buildroot] Add support for Cube2.0 to Buildroot 0003792: [Buildroot] Add support for fsimx7ulp architecture to Buildroot 0003773: [Buildroot] Some device trees for F&S boards are not built 0003764: [Display] Add support for Wayland/Weston 0003774: [Bluetooth] Add xrandr to F&S configs to allow minimal display rotation 0003769: [Buildroot] Add wget to F&S boards 0003766: [Buildroot] Add virtual keyboard to Matchbox WM 0003772: [Buildroot] /etc/init.d/S35x11 always starts X11 even if no framebuffer is available 0003771: [Bluetooth] Buildroot has busybox-1.24.x, but F&S defconfig for busybox is still 1.23.x 0003770: [Buildroot] In the rootfs there appear some paths from the build host 0003767: [Buildroot] If no login_tty is given syslog grows rapidly

0003763: [Buildroot] Clean up F&S defconfigs 0003762: [Buildroot] The download sequence for CubeA7UL does not work

0003761: [Buildroot] Final fixes before release

0003590: [Buildroot] Have a Qt5 configuration for fsimx6 0003589: [Buildroot] Handle new device tree names for F&S boards and modules 0003588: [Buildroot] Update Buildroot to buildroot-2016.05 0003587: [Buildroot] Use gstreamer-1.x on fsimx6 0003586: [Buildroot] Switch fsimx6 to kernel 4.1.15 using device trees 0003585: [Bluetooth] Add support for cubeA7UL 0003584: [Buildroot] Switch to newer toolchain based on gcc-5.x 0003583: [Buildroot] Support Media Transfer Protocol (MTD) 0003582: [Buildroot] Update Buildroot to buildroot-2016.02 0002706: [Buildroot] Merge own build process for Linux kernel (localdir) with the one of regular buildroot 0001847: [Display] Add DRI support to enable EGL rendering in X11 0003581: [Buildroot] Package ncurses-5.9 fails to build with gcc-5.x

0003580: [Buildroot] Option -mach=armv7-a generates compiler warnings 0003069: [Buildroot] Re-organize final scripts for F&S boards 0003070: [Buildroot] Add support for i.MX6 SoloX (fsimx6sx) 0003071: [Buildroot] Add proper GPU support for i.MX6 SoloX 0003068: [Buildroot] /etc/profile.d is a regular file instead of a directory 0003067: [Buildroot] Update Buildroot to buildroot-2015.11.1

0003064: [Buildroot] Switch default touch support from tslib to evdev on fsimx6 0003063: [Buildroot] Update to busybox-1.23.x on F&S boards 0003577: [Buildroot] 3D graphics and video playback do not work on kernel 3.0.35 0003576: [Buildroot] Keys for ssh are computed even if rootfs is read-only 0003062: [Buildroot] gst-fsl-plugins do not work in buildroot-2015.05 on fsimx6 0003061: [Buildroot] Fix defconfig problems when building Linux kernel 0002701: [Buildroot] Update Buildroot to 2015.05 0002700: [Buildroot] Update Buildroot to 2015.02 0002699: [Buildroot] Update Buildroot to 2014.11 0002698: [Buildroot] Update Buildroot to 2014.08 0002697: [Buildroot] Update Buildroot to 2014.05

0003066: [Buildroot] Add support for i.MX6 UltraLite (fsimx6ul) 0003579: [Buildroot] libpng fails to build under Buildroot 0003065: [Buildroot] Update buildroot to buildroot-2015.08.1 0003060: [Buildroot] Midori compilation fails in buildroot-2014.xx 0002666: [Buildroot] Pango and cairo compilation fails because of a bad libtool file (.la) 0002653: [Touch driver] X-Server crashes when tslib accesses /dev/input/event1 0002651: [Buildroot] Package x11r7/xdriver_xf86-input-tslib fails to download 0003059: [Buildroot] Fix tslib crash with unknown xf86XInputSetScreen 0003058: [Buildroot] Fix download site for xdriver_xf86-input-tslib 0002709: [Buildroot] Add support for HGATEWAY board rev. 1.10

0002705: [Buildroot] Change Linux compilation to use output/build/linux-localdir 0002708: [Buildroot] libfslcodec and libfslparser don't work on fsimx6 0002707: [Buildroot] Add generic fsimx6_std_defconfig and fsimx6_min_defconfig 0002038: [Buildroot] Join i.MX6 BuildRoot with Multi-Platform-Linux 0002704: [Buildroot] Add useful alias commands like ll for ls -l, etc. 0002703: [Buildroot] Switch to busybox-1.22 0002702: [Buildroot] Add support for HGATEWAY 0002696: [Buildroot] Update Buildroot to 2014.02 0002695: [Buildroot] Update Buildroot to 2013.11 0002694: [Buildroot] Update Buildroot to 2013.08 0002693: [Buildroot] Update Buildroot to 2013.05

0002295: [Buildroot] Allow Linux compilation from a local directory 0002294: [NAND-FMD] Change UBI LEB size to 0x1f000 for new NAND driver on Vybrid 0002118: [Audio] Add alsa to gstreamer-plugins-good 0002195: [General] Use login_tty as provided by /sys/bdinfo in BuildRoot

0001469: [Production/Installation] OpenSSH key generation fails because root filesystem is read-only 0002028: [Buildroot] Qt download site has changed 0002027: [Buildroot] Move F&S specific configuration files to the subdirectories 0002026: [Buildroot] Add support for CUBEA5 0002029: [Touch driver] Calibration sometimes fails

0002025: [Buildroot] Merge BuildRoot for fsvybrid and Multi-Platform-Linux 0002024: [Serial Driver/Interface] root can not login on PicoCOMA5 0002023: [Buildroot] Use single toolchain 0002022: [Buildroot] Add mcc_pingpong 0002021: [Buildroot] Add support for mqxboot 0002020: [Buildroot] Add generic support for MCC and MQX 0002019: [General] Create link for lib/ld-linux.so.3 if required 0001582: [Cross-Toolchain] Switch to new fs-toolchain-4.7.2 and gdb-7.4.x

0001866: [Tool/Utility] Add xinput-calibrator application

0001842: [Kernel] Integrate release version modules into rootfs image 0001846: [Display] Add X11 display driver 0001840: [Buildroot] blackbox window manager causes "Segmentation fault"

0001744: [Display] Add directFB support 0001823: [Buildroot] Update to imx-lib version 3.0.35-4.0.0 0001805: [gstreamer] Add hw accelerated video processing support (VPU) and freescale specific gstreamer plugins 0001820: [gstreamer] fsllibs required by gstreamer are not available in library path 0001803: [General] Update to buildroot 2013.05

0001467: [Buildroot] Create and release first Buildroot package for FS-i.MX6 platforms (QBlissA9)

0001332: [General] Move board-specific files from target/device/f+s to board/f+s 0001331: [General] Rebase BuildRoot to version 2012.08 0001306: [General] Added PicoCOM4, PicoMOD7A and NetDCU14 0001303: [Display] Add VNC server for X11 display. 0001295: [General] Add GDB Server 0001284: [Display] Configure Xorg for Samsung Touch 0001291: [NAND-FMD] Add busybox tools to access MTD 0001292: [General] Add SSH (OpenSSH) 0001285: [Display] Can not run X applications in default configuration 0001308: [General] Add HDMI to PicoMOD7A 0001286: [Display] Touch: Xorg calibration reports 'Mis-click detected'

0004631: [NBoot] add reboot command 0004632: [NBoot] change NAND erase function keys 0004633: [NBoot] add BadBlock check function 0004634: [NBoot] add NAND test 0004635: [NBoot] mark and check BadBlock marker in first tree pages of block 0004636: [NBoot] add NAND functions for raw access 0004637: [NBoot] fix error in ldscript 0004638: [NBoot] fix Makefile for changes in ldscript 0004630: [NBoot] remove USB functionality

0001724: [Serial Driver/Interface] Enable internal Pull-Ups on Serial interface pins by default 0003286: [NBoot] New flash not detected

0001325: [SD/MMC] Initialize SD-Pins only when required

0000887: [NBoot] Verify NBoot checksum before storing into flash. 0000886: [NBoot] Add support for additional 128MB memory chip.

0000885: [NBoot] Add support for 128MB of RAM. 0000884: [NBoot] Correct detection of HW revision 0000883: [NBoot] Remove automatic deployment supported.

0000882: [NBoot] SD boot needs updated. Remove some debug messages. 0000881: [NBoot] Some modifications are requried for automatic deployment process.

0000880: [NI2C] Add possibility to store UBoot into flash

0000879: [NBoot] Add SD card support

0006514: [U-Boot] [FSIMX8M*] Include imx_tmu driver for fsimx8m(m/n/p) 0006515: [U-Boot] [FSIMX8MM] Fix USB handling for fsimx8mm 0006516: [U-Boot] [FSIMX8M*] Adjust size of CMA only for DRAM > 1GB 0006513: [U-Boot] Add support for OSM8MM

0006466: [U-Boot] Improve boottime for fastboot 0006465: [U-Boot] Support output of checksum in fsimage 0006464: [U-Boot] Add support for armStoneMX8MP Rev 110

0006399: [U-Boot] Improve RAM timings for PicoCoreMX93 0006415: [U-Boot] Improve bootloader env. handling for fsimx93 0006414: [U-Boot] SPI_B: Improve picocoremx93.dtsi 0006413: [U-Boot] In imx8m/soc.c, rename board_fix_fdt() to arch_fix_fdt() 0006412: [U-Boot] Improve build process for fsimx93 0006411: [U-Boot] Split fsimx93_deconfig in two configurations 0006410: [U-Boot] Improve picocoremx93 device tree 0006409: [U-Boot] Improve fsimx93 board configuartion 0006408: [U-Boot] Improve functionality for fsimx93 0006407: [U-Boot] Remove unused function for android 0006406: [U-Boot] Add F+S common configuartion 0006405: [U-Boot] Add fs common functionality for fsimx93 0006404: [U-Boot] Enable fs_eth_common function for iMX9 architecture 0006403: [U-Boot] Improve fs_fdt_common functionality 0006402: [U-Boot] iMX9: Rename board_fix_fdt() to arch_fix_fdt() 0006401: [U-Boot] Initialize lpuart[3-8] root clocks 0006400: [U-Boot] Add a per clock for lpuart3 to lpuart8 0006398: [U-Boot] Improve fs-osm-sf-mx93-adp-osm-bb-u-boot.dtsi 0006397: [U-Boot] Adjust lpddr4 timings for osm 0006396: [U-Boot] Update fsimx93 to 2024.04 0006395: [U-Boot] Update defconfig to 2024.04 0006394: [U-Boot] Add nxp version of u-boot-2024.04 0006319: [U-Boot] fsimx93: Handling of thermal zones for different cpu types is not supported

0006462: [U-Boot] [EFUSMX8MP] Fix USB device in Device-Tree 0006461: [U-Boot] [FSIMX8M*] Support files up to 64MB for bootm 0006460: [U-Boot] Add fs_selftest support 0006459: [U-Boot] Add board-cfg entries to bdinfo in Linux kernel 0006458: [U-Boot] [PCoreMX8MP/r2] Fix first access for sd cards 0006457: [U-Boot] [FSIMX8MP] For saveenv check if the current HW partition on eMMC changed 0006456: [U-Boot] [ADP-NDCU2PCORE] Add hotfix configuration for SD_A 0006455: [U-Boot] [FSIMX8MP] Move VLCD_ON and BL_ON to UBoot Device-Tree 0006454: [U-Boot] [FSIMX8MP] Fix handling of slow USB devices for xhci 0006357: [U-Boot] Configure defaut RDC Configuration for the M7 on fsimx8mp 0006453: [U-Boot] [FSIMX8MP] Move USB handling to UBoot Device-Trees 0006452: [U-Boot] [fsimx8mp] Support boards with DRAM greater than 3GB 0006356: [U-Boot] Add loading of secondary Images to fsimx8mp

0006233: [U-Boot] Update fsimx6 boards to U-Boot 2021.04

0006194: [U-Boot] Uboot for fsimx6ul-Y2024.03

0006191: [U-Boot] Update Secure Boot to new release 0006192: [U-Boot] Update fsimx8mn to U-Boot 2021.04 0006190: [U-Boot] Add support for loading secondary SPL and Uboot

0006116: [U-Boot] Remove SHA256 support for fsimx6sx 0006112: [U-Boot] Update fsimx6sx boards to U-Boot 2021.04

0006030: [U-Boot] Remove SHA256 support for fsimx6ul 0006031: [U-Boot] Update fsimx6ul boards to U-Boot 2021.04

0006005: [U-Boot] Addfsheader.sh: Check for crc32 and xxd before using them 0006004: [U-Boot] Fix default entry for environment in NAND

0005986: [U-Boot] Update fsimx8mm architecture to Uboot 2021.04 0005985: [U-Boot] On fsimx8mm, add old device tree names for compatibility 0005984: [U-Boot] Add command fsimage boot to show current boot settings 0005982: [U-Boot] Drop board revision from BOARD-CFG names 0005940: [U-Boot] F&S Update for files bigger that 2GB fails

0005939: [U-Boot] Uboot is now located in the boot partition of eMMC 0005937: [U-Boot] Relocate U-Boot and Environment in fsimage save if needed 0005938: [U-Boot] Have new NAND/MMC layouts for fsimx8mm/mn/mp 0005936: [U-Boot] Nboot can now be written to NAND flash with U-Boot 0005935: [U-Boot] Introduce crc32 checksums for fsimage save command 0005934: [U-Boot] Fix bootaux command 0005933: [U-Boot] Improve Uboot versioning 0005932: [U-Boot] Update to NXP u-boot-2021.04

0005789: [U-Boot] Remove certain u-boot commands for secure boot 0005780: [U-Boot] Add functionality for Secure Boot on i.MX8MM Boards 0005781: [U-Boot] Add Option to menuconfig to toggle secure boot messages 0005782: [U-Boot] Improve functions from arch/arm/mach-imx/checkboot.c 0005783: [U-Boot] Add support for signed U-Boot Images for i.MX8M Boards 0005784: [U-Boot] Support signed Linux images on i.MX8M based Boards 0005785: [U-Boot] Add i.MX8MN support for Secure Boot 0005786: [U-Boot] Add support for op-tee 0005787: [U-Boot] Fix OC-RAM Layout for fsimx8mp 0005788: [U-Boot] Add secure boot for fsimx8mp

0006065: [U-Boot] [PCoreMX8MMr2] Ethernet led is not configured correctly 0006064: [U-Boot] [REALTEK PHY] ALDPS mode is not enabled and EEE LED indication is not disabled 0006063: [U-Boot] [FSIMX8MM] Ethernet is still enabled after booting into linux

0005667: [U-Boot] fsimx8mp: Improve fs_spl_memtest configuration in spl.c 0005666: [U-Boot] fsimx8mp: Correct some comments 0005663: [U-Boot] Increase nboot version to 2022.12 0005665: [U-Boot] Correct mmc env offset values in picocoremx8mp.dtsi 0005664: [U-Boot] fsimx8mp: Improve ram timings for picocoremx8mp(r2) 2GB versions 0005662: [U-Boot] Add history file for fsimx8mp to describe fw for nboot 0005661: [U-Boot] Improve dram timings for armStoneMX8MP-V4I 0005660: [U-Boot] ddr:imx8m: Add DRAM PLL to generate 900MHz output

0005142: [U-Boot] Update process does not fail if single command fails 0005626: [U-Boot] Improve phy shutdown for dwc_eth_qos driver 0005625: [U-Boot] Improve primary eth interface for fsimx8mp 0005624: [U-Boot] Add new environments for bootloader fs update in fsimx8mp.h 0005623: [U-Boot] Improve ethernet aliases for fsimx8mp 0005622: [U-Boot] Improve features support for fsimx8mp 0005621: [U-Boot] Add nboot configuration for PicoCoreMX8MPr2-Fert1-5 0005620: [U-Boot] Add support for picocoremx8mpr2 0005619: [U-Boot] Rework device tree for picocoremx8mp 0005618: [U-Boot] Add feature option for eth-phy-a and eth-phy-b 0005617: [U-Boot] Add nboot config for armStoneMX8MP-Fert0.100 0005616: [U-Boot] Improve USB2 support for fsimx8mp 0005615: [U-Boot] Improve nboot configuration for armStoneMX8MP-Fert4.100 0005614: [U-Boot] Add config for armStoneMX8MP-FERT5.100 0005613: [U-Boot] Fix FDT_TEMP entries for fsimx8mm/mp 0005612: [U-Boot] Add no-uboot-override to fs_fdt_set_val() 0005611: [U-Boot] Enable FS mmc common functions for fsimx8mp 0005610: [U-Boot] Fix mmc_get_env_dev(), simplify board_mmc_get_env_dev() 0005609: [U-Boot] Enable CONFIG_FASTBOOT_UUU_SUPPORT on fsimx8mm/mn/mp 0005608: [U-Boot] Revert F&S changes in iomux.c and console.c 0005607: [U-Boot] Remove usb host initialization in SPL for fsimx8mp 0005606: [U-Boot] Improve device detection on typec connector for fsimx8mp 0005605: [U-Boot] Update NBoot version for fsimx8mm/fsimx8mm/fsimx8mp to 2022.09 0005627: [U-Boot] [fsimx8mp] Disable not used ethernet nodes in device tree 0005604: [U-Boot] Fix env device for fsimx8mp 0005603: [U-Boot] Fix new RAM timings for fsimx8mm

0005573: [U-Boot] Merge tag 'fsimx8mm-Y2021.04.2' into HEAD

0005556: [General] Disable ethernet before booting linux for fsimx8mm 0005555: [General] Disable phy CLKOUT for PicoCoremx8MMr2 0005554: [General] Improve picocoremx8mmr2 device tree 0005553: [General] Enable ALDPS mode and disable EEE LED indication 0005552: [General] Move LED configuration of Realtek PHY to board_phy_config 0005551: [General] Change ingress delay for KSZ9893R Ethernet switch on fsimx8mm/mn

0003558: [U-Boot] Add support for PicoCoreMX7ULP 0005384: [U-Boot] Fix fsimx7ulp reloction error 0005383: [U-Boot] Add GIGADEVICE gd25lq80c spi nand flash support 0005382: [U-Boot] Add picocoremx7ulp spi flash device support 0005381: [U-Boot] Increase fsimx7ulp default CMA size 0005380: [U-Boot] Improve imx7ulp reset cause handling 0005379: [U-Boot] Improve imx7ulp bootaux command

0005320: [U-Boot] Improve cma setup for target fsimx7ulp 0005323: [U-Boot] Add "is_usb_boot" function for platform fsimx6sx/ul 0005322: [U-Boot] Improve is_usb_boot function for MX6 CPUs 0005321: [U-Boot] Add GPU detection for fsimx6sx 0005319: [U-Boot] Improve rndis gadget configuration on platform fsimx7ulp 0005318: [U-Boot] Add support for target fsimx7ulp 0005316: [U-Boot] lib: errno: avoid error format-overflow 0005315: [U-Boot] Backport new usb gadget driver from version v2019.01 0005178: [U-Boot] U-Boot target fsimx6 doesn´t build any more due to size of U-Boot exceeds 0005176: [U-Boot] Add new nboot config TBS2-FERT3 0005175: [U-Boot] Fix fastboot for i.MX8 0005174: [U-Boot] Set and use ecc.total/ecc.bytes correctly in mxs-nand-fus.c 0005173: [U-Boot] Fix bootcmd-fastboot override when booting from USB 0005158: [U-Boot] Update process overwrites UBoot in eMMC when USB read fails 0005157: [U-Boot] Merge own fsimx7ulp U-Boot git to F&S default git 0005156: [U-Boot] Add dynamic setup of linux device-tree within U-Boot 0005155: [U-Boot] Add support for PicoCoreMX6UL100 0005132: [U-Boot] Boards cannot boot when started with MFG tool 0005134: [U-Boot] The gpmi-nand-fus driver computes the eec byte sitze wrong

0005326: [U-Boot] Change DACR to client access control to fix cache errors 0005325: [U-Boot] Add support for command fsimage 0005324: [U-Boot] Add support for picocoremx6ul100

0005177: [U-Boot] Add support for board efusA9r2

0005172: [U-Boot] Fix commands to create F&S Updater volumes in fsimx8mn 0005054: [U-Boot] Correct boot from ubi environments to create F&S Updater volumes 0005041: [U-Boot] Add env import/export cmd

0005115: [U-Boot] Fix DTS adaption to support backwards compatibilit

0005053: [U-Boot] Fix pmoda9 LCD pads 0005052: [U-Boot] net: nfs: remove superfluous packed attribute 0005051: [U-Boot] net: nfs: remove superfluous conversions 0005050: [U-Boot] net: unaligned copying of unsigned long 0005049: [U-Boot] kconfig: Avoid format overflow warning from GCC 8.1 0005047: [U-Boot] Fix fsimx6 absolut pathes for Linux device tree adaption 0005046: [U-Boot] Fix imx6 display 0005045: [U-Boot] Fix fsimx6 usb power polarity 0004955: [U-Boot] [fsimx8mx]U-boot corruption when fixed-phy is used

0004946: [U-Boot] Add variant of PCoreMX8MN 0004945: [U-Boot] Add USB Type C OTG functionality 0004944: [U-Boot] Adjust NAND areas for fsimx8mn nboot 0004943: [U-Boot] Fix building process for fsimx8mm 0004942: [U-Boot] Remove unused folder fsimx8mx_nano 0004941: [U-Boot] In fat_fus.c, handle files > 2GB better 0004940: [U-Boot] On fsimx8mn, disable code to detect if running on secondary SPL 0004939: [U-Boot] Handle new eMMC layout on fsimx8mn 0004938: [U-Boot] Increase size for fs_sys_prompt[] 0004937: [U-Boot] Add correct fuse values for fsimx8mn 0004936: [U-Boot] Allow optional board-fdt in BOARD-CFG files 0004935: [U-Boot] Change ingress delay for KSZ9893R Ethernet switch on fsimx8mm/mn 0004934: [U-Boot] Add -ddr3l/-lpddr4 to device tree names for fsimx8mm/fsimx8mn 0004933: [U-Boot] Change fsimx8mn to use NBoot 0004932: [U-Boot] Move enum fsimg_mode from fs_image_common.h to fs_image_common.c 0004929: [U-Boot] Increase NBoot version to 2021.07

0005262: [Kernel] Improve iomuxc support and emmc support for fsimx6ul 0005261: [U-Boot] Improve PicoCOMA7 lcd and usb setup 0005260: [U-Boot] Add support for command fsimage 0005259: [U-Boot] Improve emmc layout for target fsimx6ul 0005258: [U-Boot] Add support for same defconfig independent from boot device fsimx6ul 0005257: [U-Boot] Add support for picocoremx6ul100 on platform fsimx6ul

0004926: [U-Boot] Add config for PCoreMX8MM-FERT13.130 0004925: [U-Boot] Add dynamic setting of cpu temp ranges for fsimx8mm 0004924: [U-Boot] Add part command to uboot console 0004923: [U-Boot] Merge architecture tbs2 into fsimx8mm 0004922: [U-Boot] Improve support for architecture tbs2 0004921: [U-Boot] Set tbs2.c UPDATE_DEF to mmc0,mmc2 0004920: [U-Boot] Improve fsimx8mm mac address setup 0004384: [General] [ARMv7][NOT RELEASED] Uboot crashes when using tftp command multiple times

0004855: [U-Boot] Improve FDT support and naming for fsimx8mx-nano 0004856: [U-Boot] Improve fsimx8mm target 0004857: [U-Boot] Improve fec_mxc fixed link support for DM 0004858: [U-Boot] Remove target fsimx8mx 0004861: [U-Boot] Improve feature support for fsimx8mm 0004860: [U-Boot] Fix compilation warnings for fsimx8mm 0004859: [U-Boot] Remove arch/arm/mach-imx/mx8mx 0004919: [U-Boot] Change NBoot version to current one 0004918: [U-Boot] Remove setting ethaddr for WLAN on fsimx8mm 0004917: [U-Boot] Improve fsimx8mm linux fdt fixups 0004916: [U-Boot] Improve fsimx8mm KSZ9893 Switch setup 0004915: [U-Boot] Improve fs_board_common environment variable setup 0004914: [U-Boot] Fix-up for devicetrees fsimx8mm 0004913: [U-Boot] Add support for resetting phy via device tree entry 0004912: [U-Boot] Fix CONFIG_ENV_SIZE to 16KB 0004911: [U-Boot] Fix DSI_PHY_REF clock settings 0004910: [U-Boot] Fix have-eth-switch config entry to have-eth-phy 0004909: [U-Boot] Set boardinfo.name to PicoCoreMX8MX for boards with 8mx config 0004908: [U-Boot] Fix addfsheade.sh for yocto build 0004907: [U-Boot] fsimx8mm: Fix handling for PicoCoreMX8MX 0004906: [U-Boot] fsimx8mm: Add all current BOARD-CFGs 0004905: [U-Boot] Add CONFIG_SPL/TPL_AUTOBUILD, do not build SPL by default on fsimx8mm 0004904: [U-Boot] fsimx8mm: Handle device tree fixup more cleanly 0004903: [U-Boot] fsimx8mm: Drop debug output, rename MTD partition Spl to NBoot 0004902: [U-Boot] Fix nand_spl_load_image() in case of bad blocks 0004901: [U-Boot] Also write U-BOOT files in command fsimage save 0004900: [U-Boot] Also use indendation in scripts/fsimage.sh 0004899: [U-Boot] fsimx8mm: Add MMC loading/saving, refactor fsimage code 0004898: [U-Boot] fsimx8mm: Have separate nboot-info for NAND and MMC 0004897: [U-Boot] fsimx8mm: When loading U-Boot, provide offset values from nboot-info 0004896: [U-Boot] Allow NAND environment offsets in device tree 0004895: [U-Boot] fsimx8mm: On eMMC, load environment from boot partition 0004894: [U-Boot] Handle kernel, fdt and rootfs according to boot device 0004893: [U-Boot] fsimx8mm: Add fuse subcommand for fsimage 0004892: [U-Boot] fsimx8mm: Get rid of fs_nboot_args and use cfg_info instead 0004891: [U-Boot] Add fsimage command to handle NBoot images 0004890: [U-Boot] Allow using function fdt_print() from outside of cmd/fdt.c 0004889: [U-Boot] fdt_support.c: Fix bug in fdt_getprop_u32_default_node() 0004888: [U-Boot] fsimx8mm: Identify boot system with NXP boot devices 0004887: [U-Boot] fsimx8mm: Add nboot-info for BOARD-CFGs, use .*.tmp files in Makefile 0004886: [U-Boot] Move fs_image.[ch] from fsimx8mm to common 0004885: [U-Boot] Have environment in NAND or MMC on fsimx8mm 0004884: [U-Boot] Use new MTD partition layout on fsimx8mm, clean up boot srategies 0004883: [U-Boot] fs_image.c: Have two copies of BOARD-CFG and FIRMWARE 0004882: [U-Boot] mxs_nand_spl: Do not stop when ONFI version is unknown 0004881: [U-Boot] mxs_nand: Reduce malloc usage in SPL 0004880: [U-Boot] cli_hush: Add support for indirect parameter expansion 0004879: [U-Boot] Add fs_board_get_boot_device_from_fuses() to fs_board_common.c 0004878: [U-Boot] Add nboot build process for fsimx8mm 0004877: [U-Boot] Change SPL on fsimx8mm to use F&S NBoot images to boot 0004876: [U-Boot] Add fs_image library to load and handle F&S images on fsimx8mm 0004875: [U-Boot] Add streaming option to SDP protocol 0004874: [U-Boot] Fix Kconfig prompt for MXC GPIO driver 0004873: [U-Boot] Add fsimage script 0004872: [U-Boot] New version of addfsheader as a script, remove old C version 0004871: [U-Boot] Add Kconfig options to create a disassembler listing 0004870: [U-Boot] Also use memalign_simple() in SPL, not only malloc_simple() 0004867: [U-Boot] Append for commit "Add support for I2C_GPIO to configure switch on fsimx8mm" 0004866: [U-Boot] Add support for I2C_GPIO to configure switch on fsimx8mm 0004865: [U-Boot] Improve fsimx8mm mac address setup 0004864: [U-Boot] Improve fsimx8mm SPL settings

0004505: [U-Boot] Improve support for target fsim8mm 0004845: [U-Boot] Improve bd71837 pmic driver 0004844: [U-Boot] Improve fsimx8mx support 0004843: [U-Boot] Improve uart4 support for tbs2 0004842: [U-Boot] Add FS Update Support for fsimx8mm 0004841: [U-Boot] Disable display support for fsimx8mx_nano 0004840: [U-Boot] Add fsimx8mx_nano support 0004839: [U-Boot] Improve fsimx8mx defconfigs 0004838: [U-Boot] Improve linux,cma size settings for fsimx8mx 0004837: [U-Boot] Disable display support for fsimx8mx 0004836: [U-Boot] Fix build warnigs for n535521 mipi driver 0004835: [U-Boot] Improve MIPI-DSI PMS restriction values 0004834: [U-Boot] Improve support for static board config 0004833: [U-Boot] Fix fsimx8mx nand defconfig 0004832: [U-Boot] Use legacy ethernet driver for fsimx8mx 0004831: [U-Boot] Improve DRAM size detection for fsimx8mx 0004830: [U-Boot] Improve DRAM size configuration for fsimx8mx 0004847: [U-Boot] Improve fixed config for fsimx8mx 0004846: [U-Boot] Add possibility to set cma size via DTS for fsimx8mx 0004829: [U-Boot] Fix fsimx8mx RAM timings 0004828: [U-Boot] Add support for target TBS2 0004507: [U-Boot] Wrong character in debug messages 0004506: [U-Boot] Add support to read phy address from device-tree for fec_mxc 0004504: [U-Boot] Improve USB and Display support for PicoCOMA7 0004502: [U-Boot] Improve IOMUX_PAD macros 0004501: [U-Boot] Improve serial devices and netconsole implementation 0004498: [U-Boot] Board hangs for devices which have MMC as bootdevice

0004323: [Display] Add support for target fsimx8mm 0004503: [U-Boot] Add basic device tree support for serial drivers on F&S platforms

0004379: [General] [i.MX6UL] Create PicoCOMA7 release

0004397: [General] Create PicoCoreMX6UL release to support eMMC as boot device

0004397: [General] Create PicoCoreMX6UL release to support eMMC as boot device

0004379: [General] [i.MX6UL] Create PicoCOMA7 release

0004497: [U-Boot] Improve DDR init support 0004499: [U-Boot] Improve max frequency for SDHC High Speed Mode 0004500: [U-Boot] Add support for target fsimx8mn

0003220: [U-Boot] Secure Boot Issue, saving/starting Images

0003546: [U-Boot] Secure Boot HAB header check function failure 0003482: [U-Boot] secure boot improve authentication procedure 0003481: [U-Boot] Improve secureboot HAB address verification 0003480: [U-Boot] Update UBoot secure boot branch to current release fsimx6ul-V2.1

0004496: [U-Boot] Add support for target fsimx8mm

0003953: [U-Boot] UBoot set OTG PWR polarity to active high but it´s active low 0003954: [U-Boot] Add support for PicoCoreMX7ULP revision 1.20

0004162: [U-Boot] Fix display support for fsimx6sx 0004161: [U-Boot] SPI initialization doesn´t work anymore

0004160: [U-Boot] Fix display support for PicoCoreMX6UL 0004025: [U-Boot] Add support for gar1 revision 1.40

0003479: [U-Boot] Improve auxiliary core support (Cortex-M4) in UBoot 0003738: [U-Boot] Update U-Boot to 2017.01 0003737: [U-Boot] Update U-Boot to 2016.11 0003736: [U-Boot] Update U-Boot to 2016.09 0003735: [U-Boot] Update U-Boot to 2016.07 0003734: [U-Boot] Update U-Boot to 2016.05 0003732: [U-Boot] Update U-Boot to 2016.03 0003729: [U-Boot] Update U-Boot to 2016.01 0003727: [U-Boot] Update U-Boot to 2015.10 0003760: [U-Boot] RPMsg ring buffer allocation fails with Kernel 4.9 0003759: [U-Boot] loadaddr is modified by several commands 0002680: [U-Boot] Update U-Boot to 2015.07 0002679: [U-Boot] Update U-Boot to 2015.04 0003746: [U-Boot] Add display support for fsimx6sx and fsimx6ul to U-Boot 0002523: [U-Boot] Update U-Boot to 2015.01 0002522: [U-Boot] Update U-Boot to 2014.10 0003758: [Display] Remove duplicate code for display clocks 0003757: [U-Boot] Move F&S common code to a common directory 0003756: [U-Boot] Switch F&S platforms to CONFIG_SYS_GENERIC_BOARD 0003755: [U-Boot] Reduce differences to mainline U-Boot 0003754: [U-Boot] Switch back to zImage for Linux kernel 0003753: [eMMC] eMMC with 4GB does not work in Pseudo-SLC mode 0003745: [U-Boot] Add display support for fsimx6 to U-Boot 0003752: [U-Boot] F&S source files still have license messages, should be SPDX identifier 0003751: [U-Boot] Add support for PicoCoreMX6SX to U-Boot 0003750: [U-Boot] Add support for PicoCoreMX6UL to U-Boot 0003749: [U-Boot] Add support for PicoCOMA7 to U-Boot 0003748: [U-Boot] With display support activated, U-Boot is bigger than 512KB 0003747: [U-Boot] On i.MX6, show more clocks in command clocks 0003724: [WLAN] Bluetooth does not restart after reboot 0003476: [U-Boot] QBlissA9r2: timeout on tftp boot strategy

0003852: [U-Boot] Add original U-Boot for i.MX7ULP for U-Boot

0003723: [U-Boot] Add support for i.MX6ULL to U-Boot (optionally used on efusA7UL)

0003722: [Display] Image on ET070080 is sometimes shifted to the left on efusA9 0003721: [PCIexpress] Add support for PCIe on fsimx6sx

0003715: [U-Boot] Add support for CONT1 to U-Boot 0003716: [U-Boot] Add Cortex-M4 support for i.MX6SX/fsimx6sx 0003706: [U-Boot] Patch device tree on-the-fly for run-time detected features 0003720: [U-Boot] CONFIG_NETCONSOLE does not work 0003719: [U-Boot] Add support for QBlissA9r2 to U-Boot 0003710: [eMMC] Add eMMC support to U-Boot 0003718: [U-Boot] Add option to U-Boot to use USB OTG port as a second host port 0003717: [U-Boot] Result of command in then or else part of if can not be evaluated after if 0003698: [U-Boot] Add support for PicoCOMA9X to U-Boot 0003714: [U-Boot] The DEL key does not work on the command line in U-Boot 0003713: [Ethernet] Ethernet PHYs are active in Linux after booting even if Network is never used 0003711: [U-Boot] Check GPIO to decide between Recover and Update procedure 0003709: [U-Boot] efusA9 does not boot with 2GB RAM 0003708: [U-Boot] Add support for GAR1 to U-Boot 0003707: [U-Boot] udelay() delays too long 0003703: [U-Boot] Add support for NetDCUA9 to U-Boot 0003700: [U-Boot] Add support for PicoCOM1.2 to U-Boot 0003705: [Ethernet] WLAN can not have an own MAC address 0003704: [U-Boot] Drop mach-ID stuff from code, handle board features similarly on F&S boards 0003701: [U-Boot] Add blinking LED support for i.MX6UL 0003699: [U-Boot] Add support for Cube2.0 to U-Boot 0003336: [U-Boot] Support for auxiliary core (Cortex-M4) in UBoot

0002441: [Hardware] Add support for HGATEWAY in U-Boot 0002678: [U-Boot] Add support for LEDs on HGATEWAY 0002067: [USB host] Add support for USB host on Vybrid 0002373: [U-Boot] _kernel_nfs, _kernel_usb* and _kernel_mmc* are missing the bootm command 0002348: [Ethernet] Add ethernet clock source detection for fsvybrid in U-Boot

0003568: [USB host] Some USB sticks have timeouts when loading the rootfs image 0003574: [U-Boot] Add default installation path for RAM on F&S boards 0003569: [U-Boot] Improve F&S boot strategy environment 0003573: [U-Boot] Drop architecture from F&S device tree names 0003572: [U-Boot] Add support for armStoneA9R2 0003571: [U-Boot] U-Boot fails to compile with GCC-5 0003570: [U-Boot] Add status LED support for fsimx6

0003100: [U-Boot] Change fsimx6 to use device trees in the future 0003098: [U-Boot] Set bootfdt variable to allow for generic FDT loading 0003097: [USB host] Do not power-cycle USB hub ports 0003096: [Ethernet] Ethernet does not work on NetDCUA5 board 1.21 0003095: [NAND-FMD] Add nand convert command for fsvybrid

0003092: [NAND-FMD] NAND flash is sometimes corrupted 0003094: [U-Boot] Add support for loading FDT from UBI on F&S boards 0003093: [U-Boot] Blinking LEDs are not possible anymore on fsvybrid in u-boot-2014.07

0003090: [Ethernet] Improve ethernet environment 0003091: [SD/MMC] On u-boot-2014.07, SD card does not work correctly 0003087: [U-Boot] Add support for efusA7UL 0003089: [Ethernet] Use fec_mxc driver on fsvybrid 0003088: [Ethernet] Add support for second ethernet port on fsimx6sx 0003086: [Ethernet] Add support for Micrel KSZ8081 ethernet PHY 0003083: [U-Boot] Add support for i.MX6 SoloX (fsimx6sx) 0003085: [U-Boot] Add support for i.MX6 UltraLite (fsimx6ul) 0003084: [U-Boot] Add support for efusA9X 0002521: [U-Boot] Update U-Boot to 2014.07 0003082: [U-Boot] Move update code from cmd_source.c to cmd_update.c 0002520: [U-Boot] Update U-Boot to 2014.04 0002681: [SD/MMC] Environment: Add rootwait for slow boot devices, activate AUTO_COMPLETE, fix ubifs devices

0003081: [U-Boot] Convert fsvybrid to compile in THUMB mode 0002677: [U-Boot] Improve and simplify F&S environment, hide boot strategy variables 0002676: [U-Boot] Improve update infrastructure on F&S boards 0002675: [USB host] Add earlyusbinit to do an early USB device scan 0002674: [SD/MMC] Add SD card support for fsimx6 boards in U-Boot 0002673: [Ethernet] Add ethernet support for PicoMODA9 0001881: [NAND-FMD] NAND flash initialisation sometimes fails on bootup 0002568: [NAND-FMD] Add new F&S NAND access for i.MX6 to U-Boot 0002567: [U-Boot] Add support for i.MX6 DualLite/Solo on fsimx6 0002518: [U-Boot] Update U-Boot to 2013.10 0002566: [U-Boot] Join U-Boot code for PicoCOMA8 with common F&S U-Boot 0002519: [U-Boot] Update U-Boot to 2014.01 0002517: [U-Boot] Update U-Boot to 2013.07 0001845: [U-Boot] Update to mainline U-Boot version. This version already includes proper USB and SDHC support. 0002039: [U-Boot] Join i.MX6 U-Boot with Multi-Platform-Linux 0002516: [U-Boot] Update U-Boot to 2013.04 0002515: [U-Boot] Update U-Boot to 2013.01 0002514: [U-Boot] Update U-Boot to 2012.10

0002332: [NAND-FMD] Switch NAND handling on fss5pv210 and fss3c64xx to fsvybrid style 0002313: [NAND-FMD] Handle blank pages with bitflips in U-Boot on fsvybrid 0002311: [Production/Installation] Fix install script to use new boot strategy 0001412: [General] Switch to hush parser to have control structures like if...then...else...fi 0002307: [NAND-FMD] Don't reduce NAND size by skip amount

0002291: [Ethernet] Add support for Micrel PHY 8081RNA on armStoneA5, NetDCUA5, AGATEWAY in U-Boot 0002290: [U-Boot] Add support for blinking status LEDs on Vybrid 0002278: [NAND-FMD] Fix NAND read/write commands in case of bad blocks 0002292: [U-Boot] Join cubea5.h and fsvybrid.h 0002275: [General] Pass NBoot-Args to Linux 0002166: [NAND-FMD] Add support for block refreshing in U-Boot on Vybrid 0002165: [NAND-FMD] Support 16-bit Hardware-ECC on Vybrid 0002193: [U-Boot] Switch to more flexible boot strategy selection 0002161: [NAND-FMD] Flash based Bad Block Table conflicts with UBI on TargetFS 0002164: [NAND-FMD] Change mtdparts layout to support new NBootVyb >= VN08 0002162: [SD/MMC] Add support for ESDHC0 on Vybrid in U-Boot 0002163: [Ethernet] On Vybrid read MAC addresses from OTP fuses if set 0002044: [Ethernet] Store Ethernet MAC address in Controller 0002072: [Ethernet] Improve Ethernet implementation 0002160: [U-Boot] Add support for Afriso Gateway

0002091: [U-Boot] Add support for on-board LEDs 0002073: [U-Boot] Improve Update/Install to handle script in RAM and UBIFS, add recovery 0002068: [U-Boot] Add support for 500MHz on Vybrid

0002018: [Production/Installation] Checking an install/update device fails if the device list contains blanks 0002017: [General] Add support for CUBEA5

0002016: [General] Set $platform variable in lower case 0002013: [General] Remove unused Samsung stuff 0002015: [General] Pass board revision to Linux kernel via ATAG structure 0002014: [Serial Driver/Interface] Patch serial port for Linux zImage uncompressor 0002012: [SD/MMC] Remove some remaining stuff from F&S SD/MMC driver 0002011: [General] Join armStoneA5, PicoCOMA5 and NetDCUA5 to one common fsvybrid platform 0002009: [Serial Driver/Interface] Implement serial driver for fsvybrid in the same way as fss5pv210 0002010: [General] Fix ugly implementation for reset cause 0002008: [General] Merge U-Boot for fsvybrid and fss5pv210 0002007: [General] Add support for NetDCUA5

0001864: [U-Boot] MAC address not passed into kernel

0001837: [U-Boot] Add U-BOOT pattern to detect image type in Nboot

0001814: [NBoot] Receive boot parameters from NBoot 0001727: [General] Rename board specific implementation to a common name usable for all modules from F&S: mx6q_qblissa9 -> mx6q_fs 0001567: [Kernel] Use ATAG param to pass hardware specific information into kernel. 0001548: [Hardware] Detect board HW revision 0001543: [Ethernet] Assert nRST during init (HW rev. 1.20).

0001604: [General] Setup environment for NAND and configure default settings 0001721: [Ethernet] Use internal PLL to generate clock for ETH PHY is unstable 0001667: [U-Boot] Setup for RMII_CLKOUT

0001488: [NAND-FMD] Increase kernel partition size 0001466: [U-Boot] Add new bootcmd evironment variables to combine net-mmc and net-nand boot staggies 0001465: [U-Boot] Add GBit Ethernet support

0001413: [General] Set environment variable for board name and architecture 0001326: [U-Boot] Rebase U-Boot to 2012.07 0001290: [U-Boot] Correct 'bootnfsdhcp' command line in FSS5PV210 configuration file 0001273: [Serial Driver/Interface] Improve serial driver for S3C64XX to allow CONFIG_SERIAL_MULTI 0001272: [U-Boot] Allow a dynamic environment size depending on NAND flash type 0001262: [U-Boot] Add support for PicoMOD7A and NetDCU14 0001259: [U-Boot] Combine PicoCOM3 and PicoMOD6 to a common S3C64XX platform 0001258: [NAND-FMD] Support different ECC computation modes for NBoot and the other partitions in NAND 0001257: [NAND-FMD] Allow dynamic MTD partition sizes depending on NAND flash type 0001256: [NAND-FMD] Allow NAND flashes with different block sizes 0001254: [U-Boot] Add commands update and install to manually trigger update/installation 0001253: [U-Boot] Long filenames not fully supported on VFAT devices 0001255: [SD/MMC] fss3c64xx: Switch from F&S NBoot driver to generic MMC driver 0001328: [U-Boot] Allow special argument value '.' to keep the default value 0001260: [Serial Driver/Interface] Allow different serial debug ports depending on board type 0001327: [SD/MMC] fss5pv210: Fix generic sdhci driver 0001333: [U-Boot] Improve update function (previously called autoload)

0001464: [General] Create first U-Boot version for QBlissA9 (based on 2009-08)

0000940: [SD/MMC] SD card not detected for autoload

0000928: [USB host] USB stick not detected during boot

0000940: [SD/MMC] SD card not detected for autoload

0000928: [USB host] USB stick not detected during boot