Scheduled For Release 2098-11-20
0005288: [MISC] A pull up resistor is necessary for I2C_IRQ and I2C_INTn signal.
0005284: [MISC] No reference points for the soldering machines
0005279: [Hardware] Pull-Up at RESET pin on TSC2004 needed
0005278: [Hardware] Exchange J3 and J4
0 of 4 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2022-08-11
0005484: [MISC] Wrong PCB Marking
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-11-15
0005595: [I2C] EDID Daten können nicht abgerufen werden
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-11-15
0004492: [General] The pca9632 is powerd by VLCD
0004493: [General] The touch-reset is driven by the MIPI-reset
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-11-20
0004708: [MISC] Power the Backlight from 3.3V per default
0004706: [MISC] Touch_INT_PCA can not be used with MAX7315
0004705: [MISC] Change IC2 to Maxim MAX7315AUE
0004579: [MISC] Add Connector to power Backlight external with 5V
0004580: [MISC] Change pin assignment for new Displays
0004528: [General] PWMCTRL and LEDPWRCTRL are exchanged
0004578: [MISC] Change PCA to TCA9534
4 of 7 issue(s) resolved. Progress (57%). View Issues
Scheduled For Release 2022-04-01
0005162: [Hardware] Use I2C_IRQ directly on J2 without using GPIO Expander
0005161: [Hardware] Add VLCD supply only for J2 pin 1-2 not for PUs or supply voltage for GPIO Expander
0004707: [MISC] IC2 is not usable for this application (PCA9534 and MAX7315)
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-12-15
0005286: [MISC] Adapter does not work
0005289: [MISC] Backlight regulator is wrong type
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2099-12-31
0003728: [MISC] Change layout of KSZ8081 for smd stencil
0004773: [MISC] Change Touchcontroller to TSC2004
0004774: [MISC] Change MicroSD Shape to corrected Würth Part
0004176: [MISC] Fix problem with RMII clock
0001732: [MISC] Possibility to use USB Device as USB Host
0001747: [MISC] R10/R11 are 2k2 instead of 4k7
0001952: [MISC] Add support for Analogue camera interface
7 of 7 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2012-12-19
0001657: [MISC] VLCD MOSFET not fully open
0001522: [MISC] RTC up to 20sec fail
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2017-03-29
0003218: [Hardware] USB_HVDD connected to 0.9V, should be 3.3V
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-12-08
0005140: [MISC] Config Jumpers need to be adjusted for efusA9r2
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-01-20
0005265: [MISC] The footprint of the dcdc inductors must be corrected
0005139: [MISC] Ethernet controller does not work
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-04-13
0005790: [MISC] Mounting option for DVS is not correct
0005434: [MISC] Resistor divider for ENET_MDC is wrong
0005302: [MISC] Wrong voltage level for MDIO and MDC
2 of 3 issue(s) resolved. Progress (66%). View Issues
Scheduled For Release 2099-01-01
0005490: [MISC] Add Reset Signal on JILI-30 connector
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2022-05-31
0005435: [MISC] Resistor divider for ENET_MDC is wrong
0005436: [MISC] L21 and L22 mounted wrong
0005303: [MISC] Wrong voltage level for MDIO and MDC
3 of 3 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-09-30
0005492: [MISC] Add Reset Signal on JILI-30 connector
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-12-31
PCB Version 1.40, HW Version 1.40
0005491: [MISC] Add Reset Signal on JILI-30 connector
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-12-15
0005791: [MISC] Remove CAN
0005270: [PCIexpress] Change name and Voltage of PCIe (Standard)
0004772: [MISC] Cannot mount OSM module on carrier board
0004757: [MISC] Level translator (B.ICIF.187) pads are covered with soldermask
0004756: [MISC] reference marks are covered with soldermask
0004754: [MISC] RTC Crystal pads are covered with soldermask
0 of 6 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-08-26
0005507: [SPI] [PCOREMX6SX] SPI Clock does not get marked as shared by the spi examples so Linux disables it
0004262: [General] [i.MX6SX] [ALL]: Update all examples to new SDK_2.7.0 version
1 of 2 issue(s) resolved. Progress (50%). View Issues
Scheduled For Release 2020-08-26
0005358: [General] The RPMSG pimpong example sends ech the messages double
0004261: [General] [ALL][ALL]: Update version to sdk_2.7.0
0004260: [General] [ALL][ALL]: Update version to sdk_2.6.0
2 of 3 issue(s) resolved. Progress (66%). View Issues
Scheduled For Release 2021-03-06
0004286: [MISC] Pin1 of J14 is on the wrong side
0004110: [MISC] RTS/CTS of U25 are switched
0004237: [MISC] Wrong connection of U25
3 of 3 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-06-01
0004744: [MISC] PCB Footprint of J7 and J14 are exchanged
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-03-05
0004642: [MISC] EEPROM does not work properly
0004539: [MISC] LED Signals of J5 are exchanged if Switch Port 4 is used
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-02-26
0004643: [MISC] EEPROM does not work properly
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-07-23
0005494: [Fertigung Misc] Change PCB Array
0004650: [MISC] Increase Distance between J5 and J18
0004783: [MISC] Mount Pull-Up for mPCIe_SIM_Switch Signal
0004785: [MISC] Correct shape of L28 and L30
0004599: [MISC] SIM Holder crashes with 2mm Gap in the PCB tray
4 of 5 issue(s) resolved. Progress (80%). View Issues
Scheduled For Release 2014-09-01
0001953: [MISC] Add support for Analogue camera interface
0003726: [MISC] Change layout of KSZ8081 for smd stencil
0004233: [MISC] Revision numbers are not correct
0002316: [MISC] LAN clock on Vybrid inverted
0002321: [MISC] decoupling SD card missing
0002322: [MISC] add softramp capacitor for VLCD
5 of 6 issue(s) resolved. Progress (83%). View Issues
Scheduled For Release 2014-09-11
0002352: [MISC] Ethernet LINK or data transmit fails on rare condition with KSZ8021 or KSZ8081
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2099-12-31
0004586: [MISC] Touch controller is EOL
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2016-12-31
0003169: [MISC] No separate reset signals for WLAN and ethernet PHY
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2012-03-27
0000978: [Display] VDDCAM not supplied
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2013-08-21
0001850: [Hardware] I2C Clock and DAT exchange
0001874: [Hardware] battery current >1mA for CPU RTC
0001873: [Hardware] pulldown on LCDPOW and CFLPOW will switch on this power on power on
0001851: [Hardware] 1.5V voltage regulator cheaper type
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2013-09-25
0001891: [USB device] USBVBUS is powering board after switchon - switchoff
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2014-05-06
0002207: [Hardware] remove external RTC by CPU fix
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2099-12-31
0003287: [Hardware] no dedicated Reset for Ethernet Phys
0004587: [MISC] Touch controller is EOL
0004647: [MISC] EEPROM does not work
3 of 3 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2028-01-01
0004789: [Hardware] UART5_RTS/CTS are interchanged
0004537: [Hardware] 2nd LAN doesn't work
0004538: [Hardware] DVS feature doesn't work
0004236: [Hardware] UART5_CTS is on wrong cpu pin
0004592: [MISC] Add an 3. Reference Point on both sides
0004594: [MISC] Boostselect is not working in the Testsystem
5 of 6 issue(s) resolved. Progress (83%). View Issues
Scheduled For Release 2019-12-31
0003486: [MISC] Missing holes for the locating peg of J7 and J8
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2022-02-11
0005700: [MISC] Serial resistors of mPCIe I2C should be 0R
0005682: [Audio] The Line Signals on the featureconnector are missing decoupling capacitors
0005347: [USB device] Alternative pin for USB Type-C ALERT on J2_77 not available on PicoCoreMX8MM/Mx with i.MX8M-Nano
0005264: [MISC] Wrong supply voltage on U26
0 of 4 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2019-09-15
0004794: [Display] J14 pin 7 must be 3.3V not VLCD
0004646: [MISC] Dielectric strength of C4 is not high enougth
0004394: [Audio] Add switch so AUDIO_A_HP_L/R are not connected to J13 if SGTL5000 is not used on module
0004365: [MISC] Use SP330E instead of SP3232E for RS485 option
0004364: [MISC] Correct footprint of J1 and J2.
0004165: [USB host] VBUS voltage blocking does not work.
0004144: [I2C] Change I2C port on J10 from I2C_B to I2C_A
0003863: [Ethernet] LED of the ethernet connector wrong connection
0003862: [Display] Connect J14 pin 17 to +3V3
0 of 9 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-05-28
0005133: [MISC] Jumper option für VDD_SNVS
0004762: [MISC] Config Jumpers need to be corrected
0004763: [MISC] I2S/JTAG Jumpers need to be corrected
0004779: [MISC] WLAN Module does not work properly
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-12-28
0005141: [MISC] Problem at selecting boot mode
0004724: [MISC] RTC Clock signal is at a wrong voltage level
0004726: [MISC] BL_PWM Signal is connected to two different pins
0004727: [MISC] DISP_DATA19 has no connection
0004725: [MISC] USB_HOST Data Signals are swapped on the B2B connector
0004764: [MISC] Missing Pull-Ups on SD2_CMD and SD2_DAT0
6 of 6 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2018-06-27
0003494: [MISC] R90 for JTAG not mounted
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2018-12-27
0003725: [MISC] Change layout of KSZ8081 for smd stencil
0004385: [eMMC] For the eMMC assambly varaint, the config jumper need to be removed
0003527: [PowerManagement] Feature DVS not working
0003529: [MISC] Pull-Up´s R10, R11, R20 and R21 should be connected to VDD_SNVS
0003531: [Ethernet] Ethernet not working (no link)
0003875: [MISC] Wrong resistors for feedback pin of TPS73001
6 of 6 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2019-06-27
0004807: [MISC] Configjumper mounted wrong
0004809: [MISC] RTC is not working if R84 and R85 mounted on baseboard
0003552: [MISC] Power Audio Codec form internal 3.3V
0003884: [MISC] RTC powerconsumption too high
0004669: [MISC] Change RTC to PCF85263ATL
0004121: [MISC] Add IRQ Pin for RTC?
0004685: [WLAN] Change B.CKV.121 to B.CKV.90
0004686: [MISC] Change TPS73001 to B.ICANA.81
0004687: [MISC] D1: Use singe Diode instead of Dual Chanel BAT54AW
0004688: [MISC] Add option to power SD1-VCC from internal 3.3V or 1.8V
0004689: [MISC] Add option to power VDD_SNVS from internal 3.3V
0004694: [MISC] Change I2C-Flash to TSSOP-8
0004360: [MISC] B2B Connector Padstack shape is false
13 of 13 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-07-29
0005375: [MISC] Check if ETH_A_LED is connected to the right pin
0005374: [MISC] Change Net Name of ETH_A_LED
0005373: [MISC] Change C75 & C76 to 18pF
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-01-01
0005545: [General] PicoCoreMX8MMr2 boards get about 10 degrees hotter than PicoCoreMX8MM boards
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-08-10
0004355: [MISC] Optional Pull Down for USB_HOST_PWRn Pin
0004341: [MISC] UART_A CTS and RTS pins are connected false
0004310: [MISC] pull-up for JTAG_TRST_B should be connected to VDD_1V8
0004339: [MISC] I2C Signals of the A71CH are connected reverse.
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2099-12-31
0004616: [MISC] Board crash because of RTC
0004477: [MISC] Remove R73
0004478: [MISC] R70 needs to be connected to USB_OTG_PWR
0004479: [MISC] Add Pull-Down resistors for USB_OTG_PWR
0004481: [MISC] Add serial resistor for GPIO_J1_52 and GPIO_J1_54 for QSPI option
0004482: [MISC] Add serial resistor for AUDIO_A_GND
0004483: [MISC] Add mounting option for SAI1_RXFS and SAI1_RXC
0004484: [MISC] Route WLAN_LED to Pin ETH_B_LED
0004485: [MISC] Change Testpoints for WLAN
0004467: [MISC] Missing Testpoints
0004466: [MISC] Missing pull-up on SD_B_WP Pin
0004465: [MISC] Missing pull-up on SD_B_CD Pin
0004460: [MISC] False voltage level on PMIC I2C
0004388: [MISC] False condition of LVDS_STBY Pin
0004387: [MISC] False voltage level on LVDS chip
0004389: [MISC] Change the RTC Chip
16 of 16 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2099-01-01
0005596: [MISC] Check if ETH_A_LED is connected to the right pin
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-10-30
0004629: [MISC] EEPROM does not work properly
0004618: [MISC] Board crash because of RTC
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-01-18
0004730: [MISC] WLAN PDn pin is at a false voltage level
0004473: [MISC] SE050 Schematic Symbol does not match the layout footprint
0004663: [MISC] SD_B_VCC Voltage is set incorrect
3 of 3 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2021-03-10
0005652: [MISC] Wrong voltage supply for NVCC_SAI1_SAI5 & NVCC_ENET
0005593: [MISC] WLAN_RST is on 1.8V CPU Domain
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2019-10-23
0004420: [MISC] Configure GPIO3_1 as GPIO in pin_mux crashes flexSPI transfer
0004338: [MISC] Bootselect is not connected
0004324: [Hardware] Change standard assembly of the SGTL5000
0004319: [Hardware] Pull up is missing on the software I2C
0004078: [MISC] Connect HW-I2C to I2C_B on B2B-connector for touch display support
0004020: [MISC] SPI chipselect is connected with wakeup of RT1050
0004006: [MISC] Pin designator of schematic symbol for Y1 are wrong.
0004005: [MISC] Pull-Up on CLKOUT (U4) is missing
0 of 8 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2012-03-27
0000992: [Hardware] RTC ungennau
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2012-03-26
0000979: [Camera] Camera interface signal PCLK not routed
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-08-30
TSC2004
0005513: [MISC] Change to TSC2004
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2012-02-29
0001960: [MISC] sometimes CPU doesnt boot by freescale issue
0001959: [MISC] BOOTSEL doesnt move board to USB boot
0001958: [MISC] conflict by using WDTRIG on DISP_DAT8 with PWM1 for FAN_PWMOUT
0001957: [MISC] SW problems by using SD1_CD pin for GPIO
0001527: [MISC] Reorder RTC_IRQ pin.
0001537: [MISC] ATX functionality (PWRBTN, PM_SLP_S3n) doesn't work
0001494: [MISC] Annoying Pull-Down on Pin SPI_CS1 (Pin 202)
7 of 7 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2012-12-31
0001497: [MISC] All RTS and CTS signales are interchanged
0001504: [MISC] Add additional serial interface on EXCD0/EXCD1 Pins (QSeven Spec 2.0)
0001507: [MISC] Add On-Board uSD-Slot. Only usable if WLAN is not populated.
0001506: [MISC] Remove external Ethernet MII on PCIe Slots 1 and 2
0001495: [MISC] Internal RTC consumes to much power. Add external RTC instead.
0001502: [MISC] Reorder Data-Pins on Camera-Interface
0001500: [MISC] Add additional Software I2C Pins which replaces native I2C used for HDMI/DDC
0001501: [MISC] Add PCI-Wake Pin
0001498: [MISC] Add Reset pin for Ethernet PHY.
0001503: [MISC] Rework Power-On sequencing of power management chip.
0001499: [MISC] Remove internal SPI Flash
0001496: [MISC] Add new JTAG pin connector for DS-5
0001536: [MISC] add config jumper
0001505: [MISC] Rework Suspend-Pin functionality
0001493: [MISC] Gbit Ethernet not working
15 of 15 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2013-01-18
0001574: [MISC] I2C EEPROM write protected
0001573: [MISC] WLAN doesn't work
0001559: [MISC] doesnt start at power up on F&S Startintf
0001706: [MISC] wrong transistor for LVDS VLCD
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2019-02-19
0003731: [MISC] Change layout of KSZ8081 for smd stencil
0003539: [Ethernet] Remove R68 and R81 for different phy address.
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2106-02-07
0000293: [WinNDCUConfig] The user has no information when loading some settings via ActiveSync
0000294: [WinNDCUConfig] IO-Pin number shown in pin configuration dialog
0000295: [WinNDCUConfig] Unnecessary "reg create key" commands in exported ndcucfg script
0000296: [WinNDCUConfig] It is not possible to configure a "pure" input without any IRQ configuration.
0000297: [WinNDCUConfig] No possiblity to Importing new platform XML description files.
0000298: [WinNDCUConfig] Enable option to save registry permanently in dialog (ActiveSync)
0000292: [WinNDCUConfig] Annoying message box when aborting an export.
0000215: [WinNDCUConfig] ActiveSync connection check during the program livetime
2 of 8 issue(s) resolved. Progress (25%). View Issues
Scheduled For Release 2019-12-05
0004204: [MISC] Wrong Voltage Detector is mounted
0004190: [MISC] Change value of R45 for a lower minimum supply voltage (<15V).
0004189: [MISC] Change value of R65 from 100R to 47R.
0004174: [MISC] Improvements for ESD protection.
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2019-07-31
0003768: [Buildroot] Add support for Kernel 4.1.x to fsvybrid
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-02-07
0004208: [General] [i.MX7ULP] [DO NOT CLOSE] Check version of python-erpc package
0005268: [Buildroot] Bump busybox from 1.33.0 to 1.33.2
0004306: [General] [i.MX6_All] BR2_PACKAGE_LIBGTK3 does not build on X11 configs
0004377: [Buildroot] Add support for fsimx8mm
3 of 4 issue(s) resolved. Progress (75%). View Issues
Scheduled For Release 2020-07-27
0004380: [General] [i.MX6UL] Create PicoCOMA7 release
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2020-07-27
0004395: [General] Create PicoCoreMX6UL release to support eMMC as boot device
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2022-10-13
0005578: [General] Add armStoneA9r3 Devicetrees to fsimx6 building targets
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2023-02-28
Ist für armStoneMX8M vorbehalten.
0005732: [Audio] [aStoneMX8MP] Audio 44100Hz not supported
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2023-06-30
0005794: [Display] efusmx8mp: Wrong PWM brightness values for the default displays
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2020-02-11
0005166: [General] Add secure boot support for target fsimx8mm
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2019-07-31
0003685: [Kernel] Add fsvybrid support to F&S Kernel 4.1.15
0005117: [Ethernet] eth1 does not work on armStoneA5.2
1 of 2 issue(s) resolved. Progress (50%). View Issues
Scheduled For Release 2013-12-18
0002037: [Serial Driver/Interface] Baud rate of debug port can not be changed
0002036: [SD/MMC] SD Card is always write-protected
0002035: [Touch driver] mach-picocom4.c won't compile if s3c2410_touch is disabled
0002034: [Touch driver] Buttons sometimes need to be touched twice on Focaltech FT5x06 to be recognized
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2019-07-31
0003712: [U-Boot] Switch fsvybrid to kernel 4.1.x
0002443: [Serial Driver/Interface] Serial overflow results in off-by-one error on serial line
0002281: [NAND-FMD] ubi part does not work if the current UBI partition is erased with nand erase
0002071: [U-Boot] Check timer implementation
0 of 4 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-07-27
0004379: [General] [i.MX6UL] Create PicoCOMA7 release
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2020-07-27
0004397: [General] Create PicoCoreMX6UL release to support eMMC as boot device
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2023-06-30
0005694: [Ethernet] Change led-link from "0" to "2"
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-02-07
0005701: [WLAN] Add new mxm-wifiex driver to Yocto for Azurewave WLAN
0004270: [General] [fsimx-all] No login tty at the debug console at non fus-images
0004509: [General] Update Yocto to 3.0 (Zeus)
0005146: [WLAN] MAC address does not get passed through for Silex WLAN module
0004353: [General] The package mono-xsp can not be build because of missing host packages
4 of 5 issue(s) resolved. Progress (80%). View Issues
Scheduled For Release 2023-02-28
Ist für armStoneMX8M vorbehalten.
0005681: [Audio] [PCore8MP] Audio record is not working
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2023-06-30
0005797: [Display] efusmx8mp: Touch calibration values for RGB display not correct
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2010-11-25
0003300: [NBoot] New flash not detected
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2010-11-25
0000422: [NBoot] PicoCOM4: IO-Pin initialization adapted.
0000423: [NBoot] PicoCOM4: Executing bootloader after downloading not working.
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-12-31
new features are added under this version.
0002962: [NBoot] CAN does not work if serial debug is enabeled
0003122: [NBoot] boardfeatures not detected properly after warmboot
0003123: [NBoot] reboot with 'r' does not work on UL
0003131: [NBoot] NDA9: Serial debug on wrong port
0002318: [NBoot] Set RESETOUTn and PCIE_RSTn to high
0002319: [NBoot] debug port is needed on UART4
0002418: [NBoot] external watchdog is not disabled
0003120: [NBoot] use other clock source for timer
0002335: [NBoot] wrong Rev Jumper armStoneA9
0002289: [PowerManagement] Reset PMIC to full power after reset
0002220: [NAND-FMD] add swap block strategy for nand flash
0002221: [NAND-FMD] change block layout for nand flash
11 of 12 issue(s) resolved. Progress (91%). View Issues
Scheduled For Release 2099-12-31
0001790: [NBoot] Add support for Cortex-M4
0002050: [SD/MMC] Add support for SD/MMC
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2013-10-22
0003311: [F3S] Reading files may be slow
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2023-04-06
0005720: [Kernel] Add Windows Embedded Compact 7 updates up to 2020M06 (Update76)
0005687: [Kernel] GetTickCount may return inexact values (seen only on symmetric multiprocessing (SMP))
0005743: [Audio] Audio driver may not start (NetDCU9 only)
0005737: [CAN] Add support for armStoneA9r4
0005736: [RTC] Add support for RTC PCF85263A and PCF85063A
3 of 5 issue(s) resolved. Progress (60%). View Issues
Scheduled For Release 2024-03-03
0005482: [Touch driver] Add support for TSC2004 on PicoMODA9 for HW revision 1.20
0003523: [Audio] No Device Driver present (PicoMODA9/QBlissA9 only)
0003113: [Serial Driver/Interface] RS485 is not working (WEC7 only)
0003258: [Kernel] Storage Memory not enlargable
0003331: [CAN] CAN messages with short time distance may received in non chronologic order
0003343: [Display] Acceleration level is overwritten when display rotation is used
0003395: [Ethernet] After unplug and plug the cable connection can't be restored. (only SMSC9500)
0003439: [USB device] USB device connection works as power supply (NetDCUA9 only)
0003426: [CAN] BUS_OFF detection is lazy and happens only one time
0003483: [Kernel] WIN7: Kernel can't be installed (QBlissA9 only)
0003484: [Ethernet] Enable/disable auto negotiation and select link speed via Registry
0003057: [Display] Dual channel lvds display does not work.
0003524: [SD/MMC] Data can't be saved on the micro SD Card (PicoMODA9)
0003851: [Touch driver] ECX3000 driver hangs after a soft reset
0004448: [Kernel] Add SYSGEN_LOCALAUDIO
0003926: [CAN] 16 bits of the first two data bytes can't use for filtering using CAN_2.0B and standard frames
0005075: [CEDDK] Add/correct efus IO table for pins 167, 169.
0004525: [AIN] Add registry value to set num samples using for average calculation
0004766: [CEDDK] Pin configured as input will be reconfigured as output while write to the pin
0004827: [Serial Driver/Interface] UARTIntf driver hangs up if no adapter is plugged in
0001383: [General] Bugtracker -> Homepage
0002554: [Ethernet] Gigabit Ethernet is to slow
0002590: [eMMC] Improve IO performance
0002595: [Camera] new clock for Camera on HW Rev 1.20
0002600: [CAN] Error frames until the driver is completely loaded
0005300: [NI2C] NI2C1 does not work for armStoneA9
0002768: [Kernel] Call of SetSystemTime without Explorer.exe causes a memory leak (WEC7 only)
0005159: [Ethernet] efus without internal Ethernet chip may cause an exception while boot
0002816: [Serial Driver/Interface] Fit COMMPROPERTIES to real values
0002869: [NAND-FMD] Deleting large amout of data under ffsdisk may slow down some processes (refers FAT under EC2013 only)
0005143: [USB host] Several problems if second USB host is activated (NetDCUA9)
0002945: [EtherCAT] Add support for EtherCAT
0003126: [General] Add FSStartup feature
0003027: [Kernel] While download System SW and MAC via NBI new MAC is not accepted
0002872: [Touch driver] Add MXT224 Touch registry entries (PMA9, ASA9R2)
0003937: [RTC] RTC does not continue while power off (Beta Kernel V2.7_190401)
0005798: [Ethernet] Speed 10Mbps does not work
0004178: [Audio] Audio recording doesn´t work
0002893: [General] On the starting of a XAML application a small overlaying window frame occur
0002800: [Kernel] Small memory leak detected (12kB/h, veryfied under WEC2013)
0002762: [eMMC] Add support for 8bit data width
0002495: [Tool/Utility] Output in FSSBCProfiler_V104.exe shows some wrong values.
0002491: [CAN] Add support to receive mixed format messages (stdandard/extended)
0005341: [PWM] PWM IOMUX cfg something wrong
0005470: [Audio] Add Registry entry to divide MClk (sgtl5000 only)
2 of 45 issue(s) resolved. Progress (4%). View Issues
Scheduled For Release 2023-07-29
0003001: [Serial Driver/Interface] Implement RS485 interface
0003547: [Display] DDraw Image is corrupted when the overlay is destroyed.
0003488: [Touch driver] EDT CTP Touch may lazy while many device use same i2c bus
0003249: [NI2C] NI2C doesn´t work with battery monitor IC STC3105
0003107: [SD/MMC] Write protection does not work
0003127: [General] Add FSStartup feature
0003252: [Display] Bootloader display mode don't work correctly
0003255: [Kernel] Storage Memory not enlargable
0003353: [Audio] Driver is not loaded reliable, Bluetooth SCO audio driver may loaded with same prefix/index (WEC2013 only)
0003357: [NSPI] Data can not be received on SPI
0004767: [CEDDK] Pin configured as input will be reconfigured as output while write to the pin
0005150: [OAL] DVFC may cause reboot under special conditions (seen on PicoCOMA9X only)
0003824: [SD/MMC] Add registry value "DriveStrength"
0004573: [WLAN] Update SDMAC driver to version 2.4
0003986: [WLAN] Update SDIO8787 driver to the latest version
0004351: [Ethernet] If only one Ethernet PHY is assambled Ethernet driver does not work stable
0004534: [Ethernet] Disable ETHNETB1, access over ETHNETA1 stops working
0005402: [NAND-FMD] Start page refresh when spare area has bit flips
0003000: [Display] Rotate display via Registry cause faulty display content
0003430: [Audio] Adapt mixer to SGTL5000
0003075: [NI2C] Repeated start does not work
0003833: [General] Add Windows Embedded Compact 7 updates up to Update69 2018M09
0 of 22 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2024-03-08
0003959: [PWM] Registry value "contrastfreq" may not be conform with the adjusted frequency
0004432: [SSH] SSH SMTP Control panel applet is not working
0004768: [CEDDK] Pin configured as input will be reconfigured as output while write to the pin
0004771: [EBoot] Default output device is LVDS in spite of register "type" flag is set to RGB
0005648: [Serial Driver/Interface] Add support for transfer/receive data via DMA
0005650: [USB device] USBD works as power supply (PicoCoreMX6UL only)
0 of 6 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2017-01-31
0003043: [NI2C] Sometimes occurs an exception while boot process
0001038: [Kernel] Implement seperate cleaning of "system hive" and "user hive"
0001047: [Serial Driver/Interface] Increase the default priority of serial drivers.
0001523: [Display] No HDMI output with latest kernel image
0001571: [TVOUT driver] HDMIConfig causes error message if interface is not availabel.
0001584: [Display] Add delay to LCD power sequence for all modes
0001594: [Audio] Left and right channel seem to be interchanged
0001904: [Display] Displays drivers PWM duty cycle range depends on the adjusted PWM frequency
0002863: [CAN] Communication errors may occur while intialization phase
0001029: [Display] Silverlight doesn't handle Cursor correctly
0001551: [Touch driver] Resistiver Touch driver is not usable when multi-monitor feature is enabled
0003022: [CEDDK] Some IOs on port 4 not accessable by digital IO driver
1 of 12 issue(s) resolved. Progress (8%). View Issues
Scheduled For Release 2022-12-30
0005592: [Touch driver] TSC2004 may not work after touch down while boot process
0005452: [Display] Add support for inverted LCD_DEN voltage
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2023-01-30
0005124: [CAN] Virtual free failure
0002198: [NSPI] Add possibility to use more than one CS
0002363: [PARINTF Driver] Implement block mode
0002208: [General] Check power consumption
0 of 4 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2016-12-31
0001100: [EBoot] Can not upload PSD data from EBoot
0001163: [EBoot] EBoot > V1.05 seems to be incompatible to previous version.
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2024-01-01
0004854: [Selftest] Touch test always fails first time on MED3
0003397: [Display] DEN signal is not working (NetDCUA9 only)
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2011-07-31
0000857: [NAND-FMD] Reserve one complete flash block for MBR to avoid compaction problems
0000137: [EBoot] Disable debug output completely
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2010-03-25
0000278: [EBoot] Selftest hangs on EBoot V1.35 (64MB)
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2013-09-30
0001885: [EBoot] Change eboot debug message so that eboot prints correct boardname (NetDCU9 or NetDCU9.2)
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2014-09-30
0001886: [EBoot] Repartitioning doesn´t work correctly
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2015-01-01
0002069: [EBoot] Audio input does not work anymore when kernel is started
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2010-08-05
0003292: [EBoot] Do not check Manufacturer ID of Flash
0000333: [EBoot] PSD download (device -> host) with the current bootloader settings not working
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2018-12-01
0000668: [EBoot] Partition type not verified on PSD upload
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2009-09-30
0000134: [EBoot] Eleminate current bootscreen restrictions
0000150: [EBoot] New NBoot version where COM2 will be used for debug output
0000428: [EBoot] Use remaining memory for USB download buffer on modules having more than 32MB RAM.
1 of 3 issue(s) resolved. Progress (33%). View Issues
Scheduled For Release 2016-12-31
0000819: [EBoot] Bootloader network MAC address not initialized correctly
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-03-08
0001511: [EBoot] Add possibility to define register value presets in EBoot
0004824: [NAND-FMD] 64MB Flash: message "MECC Uncorrectable error" during boot
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2014-01-16
0000411: [EBoot] EBoot does hang in boot menu
0000391: [EBoot] RTC läuft nicht, aber RTC selbsttest OK
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2010-12-31
0000352: [EBoot] OEMGetRealTime() in ether.c reports wrong values for wDay amd wDayOfWeek
0000135: [EBoot] Eleminate current bootscreen restrictions
0000389: [EBoot] RTC läuft nicht, aber RTC selbsttest OK
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2011-12-14
0000451: [EBoot] Number of Bad Blocks is incorrect when running Selftest
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2009-09-30
0000477: [EBoot] Pass LCD settings to Windows CE kernel
0000136: [EBoot] Eleminate current bootscreen restrictions
0000390: [EBoot] RTC doesn't count. RTC selftest returns OK
1 of 3 issue(s) resolved. Progress (33%). View Issues
Scheduled For Release 2106-02-07
0000695: [EBoot] Inherit PSD after download directly and pass them to kernel.
0000754: [EBoot] Correct stack memory location in EBoot.
0000855: [NAND-FMD] Reserve one complete flash block for MBR to avoid compaction problems
0000917: [Selftest] Selftest command extended.
0000403: [EBoot] Branch current PicoMOD6 Eboot for PicoCOM3
0000731: [EBoot] Bootloader can not be entered if serial debug output is disabled
0000896: [NAND-FMD] Problems when page size is 2048 byte
0000576: [EBoot] Dutycycle is restrictesd to 30 percent
1 of 8 issue(s) resolved. Progress (12%). View Issues
Scheduled For Release 2099-12-01
0002420: [EBoot] Disable UART if serial output is disabled
0002184: [EBoot] On Vybrid read MAC addresses from OTP fuses if set
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2015-10-18
0000492: [CAN] IOCTL_CAN_WRITE_TRANSMIT_DATA returns always true.
0000862: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already.
0000972: [NI2C] Rare I2C timeouts on Samsung IIC
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2018-06-01
0001355: [Kernel] Kernel access to BINFS-Partition broken
0000409: [Display] Display driver does not work if rows > columns.
0000863: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already.
0002213: [Touch driver] Touch coordinate depends extremely on the pressure and are very inaccurately on bigger panels
0002386: [Serial Driver/Interface] WriteFile needs more time as expected
0 of 5 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2014-12-31
0000583: [F3S] Increase the number of reserved blocks
0000546: [Display] ChangeDisplaySettingsEx has a memory leak
0000317: [SD/MMC] Format is aborted using special SDHC cards.
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2020-05-06
0000971: [NI2C] Rare I2C timeouts on Samsung IIC
0000515: [F3S] Delete a some files blocks the system.
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-12-31
0002111: [Audio] Audio interface not adjustable via Registry (ND9.2 only)
0000127: [Tool/Utility] Feature NTLM-Authentification is not implemented
0000410: [I2C] I2C fails if accessed from different threads
0000484: [Touch driver] TouchPanelPowerHandler(TRUE) does not work
0000643: [Audio] LineInVolLeft/Right is not adjustable via registry
0000864: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already.
0000939: [Serial Driver/Interface] Serial driver may hang while receive data before call "CreateFile"
0001046: [Serial Driver/Interface] Increase the default priority of serial drivers.
0001354: [Kernel] Kernel access to BINFS-Partition broken
0 of 9 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2106-02-07
0001533: [I2C] Only one instance of (software) I2C driver possible yet.
0001130: [Kernel] Add SSHD Server
0000700: [Kernel] IOCTL_HAL_WRITE_BOOTINFO overwrites MAC address.
0001048: [Serial Driver/Interface] Increase the default priority of serial drivers.
0001035: [Software] Power consumption increases when display turned off via ndcucfg on WCE6 and WE7
0001020: [Display] Hardware acceleration levels using "CachedBlt" may display brocken bitmaps
0000976: [NI2C] Rare I2C timeouts on Samsung IIC
0000946: [Kernel] Registry not saved correctly if board is beeing (soft-)rebooted immediatly.
0000942: [Touch driver] Add multi-touch driver for capacitive touch modul
0000925: [Kernel] Files copied to root directory are persistent
0000616: [NI2C] Get "NI2C_FLAGS_DEVICE_NAK" when communicate very fast to a device
0000800: [Audio] Audio driver stop working
0000848: [Touch driver] Misplaced touch detection occure
0000868: [Display] PWM frequency is not adjustable by registry.
0000909: [Display] Option to disable/enable display "m-signal" not working.
0000935: [Ethernet] Board always receives new DHCP-IP address
0001397: [Tool/Utility] Add NDCUCFG Version V054
0002204: [DShow filter] HTTPStreamFilter: Adding the functions "mjpeg?init" and "mjpeg?deinit"
0001111: [Kernel] EBoot, NBoot can not be updated from EC7 kernel.
0001420: [General] Silverlight cannot be run under compact 7, especially for xip.bin
0001349: [Kernel] Kernel access to BINFS-Partition broken
0001310: [Display] Possibility to enable video memory caching
0001309: [Display] Slow display performance compared to older images
0001124: [Camera] Implement enhanced feature to retreive current camera snapshot
7 of 24 issue(s) resolved. Progress (29%). View Issues
Scheduled For Release 2019-08-31
0000021: [AIN] Analog-IN not assured agains concurrent access
0000244: [USB host] Second USB Host is not implemented into the driver
0000533: [CAN] OS does not boot if CAN chip is not present
0001125: [Kernel] Add all QFEs until 2012M02
0001778: [Kernel] Enable exFAT support
0000157: [Kernel] USB device mass storage support
0000874: [Serial Driver/Interface] Special timeout case on reading not handled correctly.
0002323: [Tool/Utility] add nboot and eboot update in TOOL(KernelUpdate)
0005145: [F3S] F3S is not working
0003421: [NAND-FMD] Deactivation of FCR doesn't work correctly.
0003419: [NAND-FMD] Add basic support for background scan of stored data
3 of 11 issue(s) resolved. Progress (27%). View Issues
Scheduled For Release 1999-12-31
0000280: [Kernel] Create XIP kernel version to enable faster bootup and reduce kernel memory consumption.
0000434: [SD/MMC] Some SD-cards can not be access correctly. Data transfer and following access hangs in this case.
0000416: [Kernel] CMD files in startup directory sometimes will not be started
0000214: [Ethernet] Detect if phy is populated.
0000036: [SD/MMC] Write-Potection on SD-Slot
0000084: [Kernel] Kernel IO-Control to disable hardware watchdog
0001779: [USB device] Reimplement USB device driver
0000104: [SPI] Implement ClockDelay and ByteDelay support
2 of 8 issue(s) resolved. Progress (25%). View Issues
Scheduled For Release 2011-12-15
0001777: [Kernel] Enable exFAT support
0001361: [CAN] Can driver may miss an interrupt.
0001350: [Kernel] Kernel access to BINFS-Partition broken
0001024: [Kernel] Add bluetooth support
0000534: [CAN] OS does not boot if CAN chip is not present
0001722: [Touch driver] TSC2007 driver hangs when touch is pressed during initialzation
0000782: [Kernel] Software reboot not working sometimes
2 of 7 issue(s) resolved. Progress (28%). View Issues
Scheduled For Release 2106-02-07
0001585: [DIO] IRQ on Pin IO48 not interrupt cappable.
0001004: [Touch driver] Add EDT Touch Driver to Kernel
0001532: [I2C] Only one instance of (software) I2C driver possible yet.
0000702: [Kernel] IOCTL_HAL_WRITE_BOOTINFO overwrites MAC address.
0000809: [CEDDK] Improve hardware register access in CEDDK library
0000973: [NI2C] Rare I2C timeouts on Samsung IIC
0002085: [NAND-FMD] Correction error occurs
0001973: [NAND-FMD] correct large block handling for f3s
0001895: [Serial Driver/Interface] COM3: stop working as soon as COM2: is open
3 of 9 issue(s) resolved. Progress (33%). View Issues
Scheduled For Release 2022-02-15
0001516: [SPI] Add custom CS handling for HW revision 1.11
0001402: [Kernel] Automatically adjust clock for daylight saving does not work
0000751: [NI2C] 0 byte messages failes
0001726: [CAN] CAN driver may hang while initialisation if pins not connected
0001510: [Display] Enable option to adjust drive strength on display signals
0001271: [DShow filter] Add additional DShow audio filters in PRO image variant.
0000691: [NI2C] Add option to disable repeated start conditions.
0001114: [Display] 2D HW acceleration may cause flickering
0 of 8 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-01-31
0000746: [USB device] Possiblity to force USB full-speed on device interface
0001103: [Software] Uhr in Taskleiste
0000538: [General] Add PowerButton driver
0000537: [Kernel] Add suspend and wakup support
0001628: [SPI] Driver methods 2 and 3 (Poll, DMA) are not supported yet.
0001050: [Serial Driver/Interface] Increase the default priority of serial drivers.
0000974: [NI2C] Rare I2C timeouts on Samsung IIC
0000558: [Serial Driver/Interface] COM2 can not be opened sometimes
0000889: [AIN] Implement AIN driver (for touch interface pins)
0 of 9 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2010-08-27
0000850: [Display] LCD not initialized correctly in combination with bootscreen.
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2012-04-01
0000551: [F3S] F3S partition is not detected correctly in case of high storage memory usage.
0001478: [Kernel] Writing PSD from kernel overwrites MAC
1 of 2 issue(s) resolved. Progress (50%). View Issues
Scheduled For Release 2019-12-31
0000970: [NI2C] Rare I2C timeouts on Samsung IIC
0000812: [NSPI] IOCTL_NSPI_TRANSFER sends wrong data
0000013: [USB host] Epson S1R72V17 USB 2.0 Host Driver (PM3) only supports one device.
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2011-07-23
0000531: [CAN] OS does not boot if CAN chip is not present
0000078: [Touch driver] Touch does not work as well as expected
0000175: [General] Reduce boot time by implementing IMGMULTIXIP
0000190: [SD/MMC] SD card is not always recognized when it is multiple times very fast inserted/removed
0000238: [Audio] Update to latest FSMixer control panel applet (Dialog size has been increased).
0000304: [DIO] Invalid error code using IRQ IOControls.
0000315: [DIO] Confgure DIO settings using "hex" values is not implemented
0000588: [Kernel] Enable exFAT support
0000550: [F3S] F3S partition is not detected correctly in case of high storage memory usage.
0000859: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already.
0000799: [Display] Add support for 2D config utility which offers dynamic configuration of acceleration.
0000842: [Display] Allow increasing framebuffer size, even when bootscreen is used.
5 of 12 issue(s) resolved. Progress (41%). View Issues
Scheduled For Release 2011-12-31
0000108: [SDK] PicoMOD4 SDK overwrites PicoMOD3 SDK
1 of 1 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2015-07-17
0001748: [NI2C] Rare I2C timeouts on Samsung IIC
0001534: [I2C] Only one instance of (software) I2C driver possible yet.
0001356: [Kernel] Kernel access to BINFS-Partition broken
0001131: [Kernel] Add SSHD Server
0001267: [USB host] Increase PhysicalPageSize default value
0001245: [Tool/Utility] Add NDCUCFG Version V053
0000905: [Kernel] Add XML-HTTP support in Pro kernel variant.
0000900: [USB host] Add custom USB-HID driver version that is able to operate with absolut positioning, which is required for USB-touch modules.
0000860: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already.
0000829: [Display] Mouse cursor is not visible (refers only ProKernel)
0000825: [CEDDK] Improve hardware register access in CEDDK library
0000810: [CEDDK] Improve hardware register access in CEDDK library
0000748: [Display] Remove blank screen in case of activated bootscreen
0000744: [Display] Unify default display modes in Bootloader and Windows CE kernel
0000742: [Display] Remove fading contrast voltage power on sequence.
0000733: [Serial Driver/Interface] Sometime it's not possible to open COM3: after boot.
0000718: [Display] DDraw surface flipping causes display flickering
0000589: [Display] Contrast value not set correctly after returning from "backlight off" mode.
0000415: [Ethernet] Second Ethernet controler does not work.
0000532: [CAN] OS does not boot if CAN chip is not present
0001001: [Display] Hardware acceleration levels using "CachedBlt" may display brocken bitmaps
0001049: [Serial Driver/Interface] Increase the default priority of serial drivers.
0002232: [Touch driver] Implement resistor between touch films into the touch evaluation algorithm
0001769: [Kernel] Implement IO-Control to update MAC address
0001512: [SD/MMC] External SD Card may not detected after warm reboot
0001398: [Tool/Utility] Add NDCUCFG Version V054
0000672: [Display] Use common lcd library which features generic method to modify power on sequencing.
0001770: [Kernel] Add IOControls for read/write Windows CE MAC address
0000699: [Kernel] IOCTL_HAL_WRITE_BOOTINFO overwrites MAC address.
0001063: [Tool/Utility] Add NDCUCFG version V050 which is based on separate ndcucfg_lib.
3 of 30 issue(s) resolved. Progress (10%). View Issues
Scheduled For Release 2019-12-31
0000975: [NI2C] Rare I2C timeouts on Samsung IIC
0000494: [Touch driver] Offset in both directions is added to real touch on screen.
0000174: [Display] After a mouse move display speed changes
0000200: [Documentation] Add Documentation for Display Driver
0000813: [NSPI] IOCTL_NSPI_TRANSFER sends wrong data
0000271: [SDK] Some files are missed in the SDK
0000189: [Kernel] Include Compact Framework 2
3 of 7 issue(s) resolved. Progress (42%). View Issues
Scheduled For Release 2011-11-11
0000832: [Tool/Utility] Does not work with WEC 7
0000831: [Tool/Utility] Move get MAC address to thread and add wait in case adapter is not ready
2 of 2 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2011-12-31
0002087: [Tool/Utility] In case of two network adapters active the same MAC is broadcasted.
0001648: [Tool/Utility] Broadcast should be triggered everytime the cable is plugged in.
0002136: [Tool/Utility] Increment retry to get MAC address to 20
0000514: [Tool/Utility] Only send broadcast after cable plugin-event
2 of 4 issue(s) resolved. Progress (50%). View Issues
Scheduled For Release 2019-07-02
0003971: [General] Adjust name of output file after selecting a new input file.
0003970: [General] Store/restore selected file type filter
0003969: [General] Add support to convert DCU PIX format to BMP
0003978: [General] Correct palette used by pix format
1 of 4 issue(s) resolved. Progress (25%). View Issues
Scheduled For Release 2009-10-31
0002215: [Tool/Utility] ComboBoxes show useless content in WEC2013 version.
0000080: [Receive] Default value for filter mask should be FFFF
0 of 2 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2014-03-31
0002885: [Tool/Utility] startup tab: Unable to set dependency > 99
0002075: [General] Use of CERDisp DLL as display driver cause an exception
0000499: [General] Collect and display driver information
0000506: [Tool/Utility] Add support for BCSend
0000513: [Tool/Utility] Add dailog to manage FTP server
0000892: [USB device] Implement pssobility to change USB function driver classes.
0000950: [Tool/Utility] Add functionality to control services
0002658: [General] C2013: Create wrong "\init" values
0 of 8 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2011-12-05
0000816: [Tool/Utility] Add option to run ndcucfg scripts.
0000524: [Tool/Utility] Only active action buttons if device side is accessible.
0000541: [Tool/Utility] Add options dialog to configure FTP programm and settings
0 of 3 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2023-12-28
0005539: [Tool/Utility] Add support armStoneA9R4
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2099-10-11
0004218: [Tool/Utility] Using Win-Reg notation empty strings can not be set
0004185: [Tool/Utility] Format volumes does not work
0000941: [Tool/Utility] Return code is always zero.
0001415: [Tool/Utility] Command "backlight on" don't save
0002883: [Tool/Utility] Can't handle whitespaces in read/write eboot/psd files
0000990: [Tool/Utility] Implement feature to import/export reg files.
0000993: [Tool/Utility] On activate a serial device it raised an exception and fail
0001176: [Tool/Utility] Add command to run a command shell within input prompt
0003110: [Tool/Utility] Command "display cursor on" does not work
0001040: [Tool/Utility] Extend the "display" command
0 of 10 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2019-12-31
0000708: [Tool/Utility] Add graphical interface to modify NBI file.
0 of 1 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2021-05-27
0000833: [Tool/Utility] Additional Download Status
0000936: [General] Modification of NetDCU-USB-Loader for manufacturing
0001660: [Tool/Utility] Relative path values do not work when USBLoader is restarted
0001923: [Tool/Utility] Starting USB-Loader from command line with parameters doesn´t work
0 of 4 issue(s) resolved. Progress (0%). View Issues
Scheduled For Release 2009-08-28
0002997: [Tool/Utility] Add command line option to start update directly and close update dialog automatically
0002340: [Tool/Utility] Create version for EC2013
0002133: [Tool/Utility] Add optional comparison of file date/version as update condition
0000310: [General] Display name of update program does not match the used platform
4 of 4 issue(s) resolved. Progress (100%). View Issues
Scheduled For Release 2017-07-24
0003217: [Tool/Utility] Error information in log-file not clearly identifiable
0000123: [General] Directories are not created automatically
0000087: [Tool/Utility] Enable some debug output
0000377: [Tool/Utility] Enable option to skip stage 1.
0000495: [Documentation] Appoint usage of ndcucfg utility
0000769: [Tool/Utility] Add command to kill process
0001622: [Tool/Utility] Add command to disable the need to reboot the device and start update directly (boot delay)
0002994: [Tool/Utility] Add command for write WCE Registry
0002995: [Tool/Utility] Add command for compare WCE Registry values
0002996: [Tool/Utility] Add command for check MD5 of files
0 of 10 issue(s) resolved. Progress (0%). View Issues