FSVybrid - Change Log

0006308: [Touch driver] Add support for FT5x06

0006227: [NAND-FMD] Bad block marker may not initialized correctly

0006079: [Kernel] Can't write NBoot from OS (WCE6 only) 0005871: [NI2C] GPIO I2C may be loaded instead of native I2C (PicoCOMA5 only) 0005967: [Touch driver] Add optional SW reset for TSC2004

0005855: [FCR] Error after long run in case BINFS is larger than data partition (FAT/F3S) 0005799: [Ethernet] Speed 10Mbps does not work 0005592: [Touch driver] TSC2004 may not work after touch down while boot process

0005452: [Display] Add support for inverted LCD_DEN voltage 0005376: [FCR] Add support for background scan of stored data 0005399: [NAND-FMD] Start page refresh when spare area has bit flips 0005377: [NAND-FMD] Add support for FCR driver (background scan of flash data) 0004815: [USB host] Activate configuration for 2nd USB host does not work

0004775: [F3S] In special case filesystem tries to write data to wrong partition 0004793: [General] Add SYSGEN_FIREWALL 0004609: [NAND-FMD] Improve ECC error handling 0004796: [F3S] Update to newest version 0004787: [Touch driver] Use calibration data from touch driver instead default windows registry 0004723: [Touch driver] Use TSC2004 as default touch driver for NetDCUA5 HW revision >= 1.30 0004720: [Touch driver] Add support for TSC2004 0004529: [Matrix keyboard] Wrong scancodes received a reboot is required for resolution

0004486: [I2C] I2C driver (via GPIO) may hang after several hours of operation 0004488: [Kernel] Call of QueryPerformanceCounter may never return 0002671: [Ethernet] ETHNETB1 may hang 0003410: [Touch driver] EDT and ILI touch drivers may effect other drivers if initialization fails

0003386: [Display] Display disruptions because of slow PWM rates (WIN2013) 0003392: [Touch driver] Add support for ILI2117A capacitive touch panel 0002993: [Touch driver] Add support for touch FT5606 0002385: [Touch driver] add touch driver support for FT5x06 controller 0003351: [Kernel] Writing PSD from OS overwrites current MAC with MAC from PSD 0003344: [Ethernet] 10MBit full-duplex or half-duplex is not working

0003041: [NI2C] Sometimes occurs an exception while boot process 0002057: [DIO] Internal pull down not working for IRQ       0002056: [CEDDK] IRQ wrongly configures pull up 0003256: [USB host] Plug in a USB device only works one time 0002629: [USB host] USB Keyboard doesn't work without USB hub 0003183: [DIO] Interrupt stop working after a while when several interurpts triggered

0002989: [Touch driver] Registry value SampleRate isn't used (only SX865x) 0003033: [Touch driver] Add registry values to change min, max pressure bounds (only SX865x) 0003031: [Touch driver] Add pen release irq handling in trigger mode (only SX865x) 0003032: [Touch driver] Add registry value to change pen detection pull-up (only SX865x) 0003019: [Display] Color depth of 8BPP does not work for all display modes

0002991: [Kernel] Can't write bootloader from Operating System (WEC7 Core Image only) 0002967: [Touch driver] SX865x Touch Driver may send multiple down-up events while one stylus down-up cycle 0002970: [Touch driver] Rework coordinate sampling routine 0002965: [PWM] Lowest frequency is restricted to 1260Hz

0002960: [Kernel] CE6: Add all QFEs until 2016M03 0002672: [Ethernet] Asign static IP is not possible 0002954: [Kernel] EC7: Add all updates until Update 58 0002953: [Kernel] C2013: Add all updates until Update 30 0002949: [PWM] Initial duty cycle setting via registry is not implemented 0002915: [CAN] Add default registry entries for PicoMODA5 0002922: [Serial Driver/Interface] Correct UART registry settings for PicoMODA5 0002911: [Kernel] Wrong time in the daylight time zone (WCE6 only)

0002303: [Touch driver] PM1.2: Add res. touch driver for PicoMOD1 SKIT 0002897: [Touch driver] Initialization of res. touch controller (SX865x) may fail

0002636: [Kernel] After approximately 28 days the system may reboot 0002777: [Touch driver] add touch driver support for tango c48 controller 0002766: [Serial Driver/Interface] Serial input into (disabled) debug line while booting causes a hang 0002740: [SPI] Chip select may be to short 0002742: [Touch driver] Add registry values to change settling time and touch rate (SX865x only) 0002618: [Kernel] Daylight-saving time while power off does not work (WCE6 only)

0002637: [Kernel] C2013: Add all updates until Update 17 0002585: [Kernel] EC7: Add all updates until (Update 45) 0002610: [General] CE2013: Batch files (.bat/.cmd) in folder StartUp are not working       0002612: [General] CE2013: Files in folder StartUp are not started by default. 0002558: [Serial Driver/Interface] NetDCUA5: Disable UARTINTF driver (NDCU-ADP-UART) by default (registry) 0002537: [Kernel] Problems while access fonts properties under .NET (maybe caused by QFE M09 2014) 0002633: [CAN] Improve CAN bus timing 0002619: [PWM] It isn't possible to set more then ca. 10% level. 0002628: [Kernel] CE6: Add all QFEs until 2015M03 0002612: [General] CE2013: Files in folder StartUp are not started by default. 0002611: [General] CE2013: Remove Active Server Pages (ASP for HTTPD), JScript and VBScript from C8E image because out of scope of license. 0002543: [Kernel] Interrupthandler of systemtimer may not called 0002550: [General] System.Exception occures by access to font property from a C# application 0002576: [Kernel] Add Aygshell to C7P kernel 0002556: [Kernel] DST (DaylightSavingTime) not working

0002083: [Touch driver] Fit EDT CAP Touch registry settings (NDA5, PCA5 only) 0002535: [Kernel] Enable SWP/SWPB assembler instructions in system control register 0002531: [Kernel] Implement Query Performance Timer 0002482: [Kernel] Improve system time precision

0002435: [Display] NEON false code by checking in 0002456: [USB host] Correct register settings for 2nd USB host 0002490: [CAN] Add support for receive mixed format messages 0002489: [Kernel] C2013: Add all updates until M11_2014 0002488: [Kernel] CE7: Add all updates from Microsoft until M11_2014 0002487: [General] CE6 updates until QFE 2014M12 0002462: [F3S] Wrong number of bytes in spare data buffer by reading empty pages. 0002455: [Display] After finishing a video last frame stays on the screen 0002430: [Display] Video window position is restricted to the upper left corner 0002419: [Serial Driver/Interface] Add support for DMA operation (Rx/Tx) 0002417: [NI2C] Slave devices can hang the bus by holding SDA low 0002399: [Display] Rotation of display via registry does not work 0002408: [Touch driver] Add support for 5-wire touch panel (sx865x driver) 0002397: [CAN] Remove debug output in case of ERROR_TIMEOUT from IOCTLs. 0002389: [CAN] Message transmition in extended mode isn't working correctly 0002372: [AIN] Readfile does not return after several cycles 0002375: [WDT] Implement Watchdog Timer 0002365: [Serial Driver/Interface] Serial driver hangs up in case of an receive buffer overrun 0002367: [USB host] Force USB Host to full speed 0002357: [RTC] NetDCUA5: Add registry settings for External RTC (only done for PicoCOMA5).

0002355: [General] CE6 updates until QFE 2014M07 0002356: [Kernel] CE7: Add all updates from Microsoft until M07_2014 0002358: [Kernel] C2013: Add all updates until M07_2014 0002324: [Serial Driver/Interface] Add UARTINTF driver (NDCU-ADP-UART) for NetDCUA5 0001836: [PARINTF Driver] Adding parintf-driver for NetDCUA5 0002205: [CEDDK] IO Pin12 and IO Pin13 interchanged (PicoCOMA5, HW REV>1.2 only) 0002350: [Touch driver] Implement restrictions (min, max) before signal Mouse-Moves to the application layer into the restitive touch panel driver 0002344: [Ethernet] add external clock detection for enet phy's 0002297: [Ethernet] Ethernet driver hangs up during ESD test

0002108: [Display] Disable mouse cursor may have no effect 0002287: [Display] Add support for 8BPP mode for LCD Display 0002186: [OAL] OEMSetRealTime failed (PCA5 Rev. 1.22, Compact 2013) 0002286: [General] Add ASP module (missing in WCE2013 only) 0002308: [Kernel] Create multi-XIP image for CE6 0002309: [Kernel] CE2013: Add all updates until update 8 M06 06/2014 0002310: [Kernel] CE7: Add M05/2014 update 0002238: [General] Add support for PicoMODA5 and PicoMOD1.2 0002304: [Display] Load ExtDLL from LCD mode 0002306: [Display] Parameter ExtDll can be set for all modes or for only one mode 0002302: [NAND-FMD] NBoot update to higher version is not possible 0002300: [Display] NDA5, PM1.2, PMA5: Switch LCD Gate drivers 0002104: [Display] Add support for display rotation via Registry 0002280: [USB device] Enable 2nd USB device cause heavy system load 0002239: [Serial Driver/Interface] Overrun in HW buffer causes invalid SW receive queue data

0002218: [Serial Driver/Interface] RTS/CTS does not work 0002201: [NI2C] Remove nine empty clocks which occur at the end of each I2C cycle 0002271: [NAND-FMD] extention for read disturbance handling 0002267: [Touch driver] Add registry values for adjust touch sensitivity to EDT touch driver 0002270: [Kernel] CE7: Add all updates until M04/2014 0002263: [Kernel] CE6: Add al QFEs until 04/2014 0002197: [Ethernet] 2nd Ethernet doesn't work on NetDCUA5 0002210: [NI2C] Implement IO Control to drive CLK line low 0002096: [CAN] Add CanCheck.exe for Compact 2103 0002216: [Display] Can't switch backlight using ast-ADP-EDT1 adapter 0002229: [USB host] Add support for 2x USB Host and 0x USB device 0002209: [Kernel] CE2013: Add UPDATE 5 04/2014

0002114: [Display] Not all parts of the display rotates 0002180: [Kernel] CE7: Add all updates until M02_2014 0002182: [Kernel] CE2013: Add all updates until M01_2014 0002189: [Ethernet] Add support for Micrel PHY 8081RNA on armStoneA5, NetDCUA5 0002126: [USB host] Implement second USB Host driver

0002092: [Ethernet] Add VLAN support 0002110: [Serial Driver/Interface] Rarely appearence of faulty RX buffer count only while parity!=N or stoppbit=2 0002139: [Touch driver] timeout for loading touch driver is too long 0002137: [NAND-FMD] Read disturbance handling 0002062: [NAND-FMD] Show ECC status information 0002105: [Serial Driver/Interface] WaitCommEvent has timeout every 5s 0002106: [Serial Driver/Interface] Add settings "7,N,2" 0002109: [NI2C] Enable, disable controler for each transfer cycle 0002107: [DIO] Add GPB18 to IO pin table (NetDCUA5 J5.1) 0002100: [NI2C] Implement bus busy detection 0002103: [AIN] AIN does not work (PCA5 only) 0002094: [CAN] Adjustment of several baudrates causes wrong values. 0002082: [Display] Add support for aSt-ADP-JHD1 0002079: [SD/MMC] Implement SW option for card detection 0002065: [Serial Driver/Interface] Implement settings "8N2" 0002060: [Serial Driver/Interface] DCB::Parity!=NONE causes errors in communication. 0002058: [Serial Driver/Interface] Provide possibility for data- and control level inversion via registry 0001978: [Serial Driver/Interface] Reduce boot time in case seriel debug output is enabled

0001971: [FS Firmware] NBoot can only written if size is 32kB 0001969: [Display] Add support for DMA operations

0001946: [Serial Driver/Interface] Enable RS485 tranceiver by registry (NetDCUA5 only) 0001883: [Kernel] Use L2 cache 0001966: [Audio] Audio doesn´t work 0001938: [NI2C] NI2C driver is not thread-safe 0001951: [USB device] Option to set USB device speed to full speed

0001945: [Serial Driver/Interface] Implement RS485 interface 0001944: [DIO] messages in debug mode don't work correctly 0001940: [RTC] Add support for external rtc (PCA8565)

0001936: [Kernel] Inherit current display settings from EBoot. 0001934: [Kernel] Add locale support for EN, DE, IT, FR 0001935: [Display] black screen by enabled bootscreen mode 0001933: [OAL] psd read and write doesn't working 0001878: [Tool/Utility] Command "serial debug off" doesn't work

0001875: [AIN] AIN doesn´t work with 1.2V reference voltage 0001890: [Display] Optimized display settings for ET070080. 0001892: [F3S] Add F3S support 0001896: [Kernel] Add touch gesture support. 0001889: [Touch driver] Add USB PCAP touch driver support.

0001882: [DIO] Some IO pins are not working. 0001855: [PWM] Adapt PWM support for HW revision 1.10 0001856: [Serial Driver/Interface] Add new serial interface configuration for HW revision 1.10 0001860: [Serial Driver/Interface] Add support for additional serial interface available on HW Rev. 1.10 0001854: [Kernel] Add support for PicoCOMA5 HW Revision 1.10 0001871: [Serial Driver/Interface] ndcucfg does not run on any serial port on NetDCUA5 0001877: [Serial Driver/Interface] Activate missing COM ports 0001876: [Serial Driver/Interface] Move registry values to separate keys for each board 0001869: [BusEnum2] Extend BUSENUM2 for board revision

0001862: [Kernel] Add special driver to correct HW issues related to Rev 1.10 0001852: [Kernel] Add FTP server 0001861: [CAN] Add support for second CAN interface available on HW Rev. 1.10 0001859: [NI2C] Correct IntPullup value usage 0001830: [DIO] IO44, IO43, and IO45 are not accessible correctly 0001822: [PWM] Add support for PWM 0001833: [Touch driver] Add stream driver support for all external touch controllers (mxt224, EDT, SX8655) 0001809: [Touch driver] Add support for resistive touch 0001821: [AIN] Add support for AnalogIn 0001844: [Display] Set BPP=16 and LCDPortDriveStrength=1 as default 0001806: [Display] Add support for 16BPP frame buffer organization 0001843: [Display] Add support for registry value LCDPortDriveStrength 0001841: [Display] Background color of buttons don't work 0001839: [Tool/Utility] Add new CheckAutoStart.exe 0001835: [Kernel] Adapt Shell Folder einvironment variables compatibel to PicoCOM2 0001834: [I2C] Only one instance of (software) I2C driver possible yet. 0001858: [Tool/Utility] The 2D Control Utility is missing

0001832: [Kernel] Add support for DMA controller. 0001636: [RTC] Add RTC support 0001702: [Audio] Add support for Audio 0001817: [CEDDK] Add IO functions for NetDCUA5 and PicoCOMA5 0001783: [NI2C] Add support for repeated start condition 0001816: [CAN] Exception when loading 2nd CAN driver. 0001785: [Display] Add new feature "Extension DLL" 0001781: [Display] Add support for backlight PWM signal 0001811: [General] Add support for FTM 0001810: [Ethernet] Get LAN interfaces more robust 0001782: [DIO] Change registry name for DIO driver to fs_digio.dll 0001787: [Kernel] IRQ handler for GPIOs only works one time 0001739: [Display] Use NEON co-processor for BitBlt optimizations. 0001784: [NI2C] Communication is very slow (1s per transfer)

0001694: [Ethernet] Add support for Ethernet 0001691: [USB host] Add support for USB Host 0001692: [USB device] Add support for USB device 0001693: [Ethernet] Add support for Ethernet 0001688: [Serial Driver/Interface] Add support for serial interface 0001741: [DIO] Add support for F&S DIO driver 0001737: [Kernel] Extend IRQ Handler for GPIO interrupts 0001705: [SPI] Implement native SPI driver (NSPI) 0001701: [CAN] Add support for CAN 0001634: [Display] First version of DCU4 based LCD driver. 0001700: [SD/MMC] Add support for SD Host

0002203: [Serial Driver/Interface] Add UART support 0001703: [I2C] Add support I2C 0001689: [NAND-FMD] Add support for NAND-FMD 0001637: [OAL] Add Interrupt Handler 0001635: [Kernel] Implement 1ms timer IRQ for sceduler 0001740: [Kernel] Disable L2 cache controller in case L2 cache is not present. 0001746: [NI2C] Add NI2C support