FSS5PV210 - Change Log

0002912: [Kernel] Wrong time in the daylight time zone (WCE6 only) 0002907: [NSPI] Default chip select does not work (NetDCU14 only) 0002853: [NSPI] Use chip select for IOPin 64 does not work in combination with other IOPins 0002843: [NSPI] Include driver to image 0002850: [NSPI] Add possibility to use more than one CS 0002779: [Kernel] Daylight-saving time while power off does not work (WCE6 only)

0002587: [Kernel] CE6: Add all QFEs until 2015M02

0002429: [NAND-FMD] Improve nand flash handling: recovery mode extension (be sure to not lose power during recovery) 0002125: [F3S] Registry is not storable (WCE6 only) 0002426: [Kernel] CE6: Add all QFEs until 2014M10 0002217: [Tool/Utility] Update ndcucfg to V0.57 0002063: [Display] Rotate display via registry entry does not work. 0002158: [Serial Driver/Interface] RTS line goes low while data transmission is not completed 0002157: [Serial Driver/Interface] Control lines are not configurable via registry

0002115: [NAND-FMD] byte order of F3S spare data must be changed 0001929: [CAN] Rework usage of several SPI registers 0001921: [F3S] Implement F3S 0001884: [CAN] Remove error debug output in case of ERROR_TIMEOUT from IOCTLs. 0001828: [CAN] Increase the CAN performance

0001768: [CEDDK] Some DIO pins do not work as expected (PM7A only) 0001773: [Kernel] Enable exFAT support 0001786: [NSPI] NSPI Mode 1 does not work 0001771: [PWM] PWM frequency cannot adjusted by registry 0001764: [Audio] Screen taps and key clicks does not work

0001750: [Camera] Initialize camera only once during bootup to reduce access delay in later applications. 0001735: [Display] Background color of buttons don't work 0001745: [PowerManagement] Display power off command does not work 0001743: [AIN] AIN reading deliver wrong values 0001736: [NSPI] Add NSPI driver 0001731: [Touch driver] Include transition resistance between touch film into the touch evaluation 0001730: [PARINTF Driver] Adding FSBus driver 0001605: [Display] Internal variable not initialized to 0 0001720: [PARINTF Driver] Register value CheckIRQ does not work as expected

0000977: [NI2C] Rare I2C timeouts on Samsung IIC 0001550: [NI2C] Sometimes many timeouts while heavy bus load

0001524: [Display] Display failures with 2D HW Acceleration 0001581: [Display] DigitalRGB interface not working in latest Kernel-Image (V1.03) 0001631: [CAN] Using two can CID2: may have mal function 0001542: [PARINTF Driver] Adding parintf-driver for NetDCU14 0001530: [I2C] Only one instance of (software) I2C driver possible yet. 0001654: [Display] It isn't possible to change the Acceleration level with the Registry 0001621: [Kernel] Add arial ttf subset 1_30 0001431: [DIO] Old style registry values like UseAsIO without A not working. 0001580: [Display] Registry LCD power sequence settings are not recognized 0001577: [USB host] Change load order of USB Host drivers to avoid initialization conflicts on bootup (e.g. WLAN stick). 0001575: [Camera] MessageQueue not deinitialized correctly which might cause maloperation when reinitailizing stream from scratch. 0001576: [Camera] Reduce camera pixel frequency to avoid image interference (MT9V126). 0001572: [Display] DEN signal is low after display initialisation 0001562: [Camera] Stream single JPEG error image in case of error. 0001563: [Camera] Make timeout to wait for Stream adjustable via registry 0001564: [Camera] Streaming will be aborted if second channel is trying to be opened.

0001432: [Camera] Update to latest camera driver and create camera kernel variant for WEC7 0001541: [Camera] Add support for camera module MT9V126 0001539: [Display] Function "DrvGradientFill" dont't work in multi monitor mode 0001540: [Camera] I2C interface to be used can not be changed via designated registry value. 0001538: [Camera] Redesign WebCam application to be more flexible. 0001525: [Matrix keyboard] Adding keyboard layouts for FR,SP,IT 0001518: [AIN] Driver hang when you call ReadFile() before touch driver is loaded.       0001517: [CEDDK] ADC_Sample() needs init of resistive touch driver to get working 0001515: [CAN] NetDCU14: CAN works only if both chips are present

0001491: [SSH] WEC7: SSHD doesn't work 0001112: [Kernel] EBoot, NBoot can not be updated from EC7 kernel. 0001116: [Kernel] NBoot / EBoot update not possible from within running WEC7 system 0001485: [Tool/Utility] Add ndcucfg V55 to image. 0001483: [TVOUT driver] Disable TVOUT driver in case HDMI is not available 0001348: [Kernel] Make sure that SMB/CIFS support is included in default kernel images. 0001369: [TVOUT driver] Add IOCTL to get back STDA_ARG_GRP_BASIC_PARAM 0001425: [DShow filter] Support Raw 264 Video format 0001481: [General] Add bluetooth modem gateway to image 0001479: [Display] Increase default contrast frequency. 0001477: [NAND-FMD] Use timing from NBOOT 0001419: [Display] Contrast voltage base frequency can not be adjusted 0001474: [DIO] Interrupt capability of DIO pins not working 0001424: [General] Add modified BINFS file system 0001422: [NI2C] nanoRISC: Add registry settings for I2C1: 0001434: [Display] HSync/VSync are constant LOW 0001433: [USB device] Under Compact 7 ActiveSync cannot work reliably, 0001343: [AIN] Analogin driver for NetDCU14 is not implemented 0001423: [General] Silverlight cannot be run under compact 7, especially for xip.bin

0001242: [Serial Driver/Interface] Enable UART3 for nanoRISC 0001414: [SD/MMC] Exceptions during boot in different modules 0001386: [Display] The Mediaplayer of Windows CE does still not play WMV

0001323: [NI2C] NI2C not working on PicoMOD7A 0001408: [Camera] PCLK from camera module on board PicoMOD7A is not same as the one from PicoMOD7 0001251: [MFC driver] No video output on HDMI 0001358: [Tool/Utility] HDMICFG: Add MULTIMON support 0001400: [TVOUT driver] Add IOCTL_STDA_GRP0_GET_PROCESSING_PARAM 0001365: [Display] Add multiple monitor feature 0001407: [Serial Driver/Interface] COM3:/UART2 is always disabled with Flags=4 0001406: [Audio] Right channel is always 0 0001403: [Display] Possibility to set QoS (quality of service) for display driver 0001394: [Tool/Utility] Add NDCUCFG Version V054 0001353: [Kernel] Kernel access to BINFS-Partition broken 0001389: [Audio] Lineout voltage level is different from PicoMod7. 0001385: [Camera] Camera MCLK present after video stream ended 0001388: [SD/MMC] PM7A: Both SD slots are not working 0001229: [CEDDK] Add IO-Table for PicoMOD7A 0001384: [DShow filter] The video stream is not stopped when the IE/Chrome/Firefox window is closed 0000966: [Ethernet] Board always receives new DHCP-IP address 0001382: [NI2C] ND14: Native I2C on connector J5 not working 0001381: [Audio] ND14: Audio not working 0001363: [Display] Correct LCD output format 0001380: [Display] Set LCDClk to 0 enables old clock calculation 0001379: [Display] LCD clock can not be adjusted 0001374: [Camera] I2C device for RawCamera is unselectable 0001376: [Display] Values for MSignal/HVSignal are not used from default display mode. 0001375: [Display] contrast +/contrast - give different results compared to contrast set. 0001160: [Display] Setting contrast value has no effect to the LBKLT_CTRL pin on ArmStoneA8 0001372: [Display] ExtEscape() wrongly returns 0 for CONTRASTCMD and others 0001368: [Display] ND14: Change default LCD mode 0001362: [CEDDK] Add function CEDDK_GetBoardFeatures2()

0001371: [Camera] I2C device to be used for Camera adapter can not be adjusted via registry 0001289: [Touch driver] Add MXT224 touch driver on PicoMOD7A 0001357: [Kernel] CE6: Add all QFEs until 2012M08 0001347: [General] Add BSP for Compact7 0001344: [DShow filter] Porting Video Module from CE6.0 to Compact 7 0001346: [Kernel] PM7A: Status LED STA1/STA2 not working 0001345: [Audio] Plays to fast after reset 0001321: [Audio] Audio doesn't work on PicoMOD7A 0001342: [CEDDK] Wrongly configures PINs as output which are not defined in registry 0001341: [Display] LCD: SetDriveStrength always outputs 0x0 0001324: [USB host] USB host has conflicts with OTG. 0001320: [CAN] CAN don't work an the PicoMOD7A 0001316: [USB host] not really supports hot plugging 0001296: [Serial Driver/Interface] ndcucfg don't run at the serial debug port on the PM7A 0001288: [Touch driver] Add MXT224 touch driver on NetDCU14 0001129: [Kernel] Add SSHD Server 0001294: [Camera] Porting Camera Module from S5PC100 to S5PV210 0001243: [Tool/Utility] Add NDCUCFG Version V053 0001187: [CAN] Change CAN driver so it can work with OSC clk 4MHz 0001401: [Audio] Audio IN Master mixer has no function

0000994: [Display] Missing video renderer for video playback. 0001153: [Ethernet] Add support for Microchip ENC624J600 0001082: [Touch driver] Add MXT224 touch driver on ArmStoneA8 0001282: [MFC driver] The Video Hardwaredecoder and DirectShow Filters are not obtained in Kernel XIPV210_CE6Pro_120827.bin.

0001266: [Kernel] Add Bluetooth support 0001265: [Kernel] Add RALink WLAN driver 0001073: [Serial Driver/Interface] Using .NET an exception may occur by call System.IO.Ports.SerialPort.Open. 0001270: [USB host] Increase PhysicalPageSize default value 0001214: [Touch driver] Resistive Touch interface not working properly

0001188: [Ethernet] Add driver for Microchip ENC624J600

0001178: [CMM driver] After playing a MP4 or H.264 video, CE6 System is crashed, 0001181: [MFC driver] MP4 and H.264 video files are always shown falsely. 0001180: [MFC driver] MFC Firmware can't be loaded. 0001179: [DShow filter] Porting the Video Module (DShowFilter, CMM, MFC, DISPLAY) from FSS5PC100 to FSS5PV210 0001189: [SD/MMC] Kernel will be crashed in devmgr.dll.

0001165: [Tool/Utility] Add NDCUCFG version V052 which is based on separate ndcucfg_lib. 0001085: [Kernel] SYSGEN_PRINTING not set 0001108: [Display] Increase default drive strength from 0x to 4x 0001106: [Display] Add support to set HSYNC/VSYNC LOW 0001150: [Display] Add possibility to set HSync/VSync signal toggle, low or high. 0001149: [Display] Add possibility to output 16bpp/18bpp/24bpp 0001088: [CAN] Extend driver so it works with two chips on the same SPI line. 0001086: [CEDDK] Extend DIO so we can have IOs which can toggle more than one pin. 0001079: [OAL] Kernel IO-Control IOCTL_HAL_GET_PBUS_SPEED no implemented.       0001078: [NI2C] I2C clock not set correctly             0001081: [Touch driver] MXT224 Touch not working on armStone 0001067: [NAND-FMD] Add support for 512MB NAND flash

0001058: [Kernel] Correct status LED so customer can measure CPU usage 0001057: [Kernel] WEC7: Increase kernel performance 0001056: [SD/MMC] Exception during boot when SD card is inserted. 0001055: [Display] Add new registry parameter VidMemCache 0001053: [Display] Adobe Flash-Movies are not shown correctly

0001044: [Kernel] Disallow paging for XIP images. 0001043: [General] Removed all registry entries regarding IRDA 0001042: [General] EC7: First version 0001041: [Kernel] EC7: remove TID/PID info from serial debug output 0001039: [Kernel] Registry erase using ndcucfg command "reg erase->reboot" not working 0001037: [Kernel] Registry erase using EBOOT command R not working 0001018: [Display] Make LCD drive strength adjustable. 0001016: [Kernel] Add support for NetDCU14 0001036: [CEDDK] Add support for armStoneA8 Rev 1.20 0001017: [CEDDK] Add support for NetDCU14 0001033: [Display] Add support for bit per pixel depth > 16 0001025: [Ethernet] 2nd Ethernet controller doesn't work

0000968: [Display] Add OpenGL support to platform 0001012: [Kernel] Add all QFEs until 2012M03 0001007: [OAL] command "serial debug on" doesn't work       0001008: [OAL] Can't access BOOTPART library 0001009: [Kernel] Init MAC address of second LAN controller 0001002: [CAN] Possibility to control debug output by zone mask (i.e. shell -c) 0000969: [CAN] CAN driver hangs if chip is not soldered 0000983: [OAL] Disable serial debug results in non-booting image       0000995: [Serial Driver/Interface] Serial port COM1: doesn't work 0000998: [CEDDK] I/O pin 11 doesn't work 0000967: [I2C] Add possiblity to adjust drive strength of I2C pins.