PicoCOM4 - Change Log

0000701: [Kernel] IOCTL_HAL_WRITE_BOOTINFO overwrites MAC address. 0000834: [Display] Enabled mouse cursor is not visible. 0004619: [Kernel] Add all QFEs until 2018M03 0004608: [NAND-FMD] Add support for large sector flash (128MB) 0001656: [NAND-FMD] Custom IO-Controls do not support large blocks. 0003021: [Touch driver] Add SYSGENs cap. touch gesture support 0002944: [Touch driver] Add support for FT5x26/FT5606 chip 0002492: [DIO] Device IO control calls refered to soft IRQs may cause a deadlock

0001775: [Kernel] Enable exFAT support 0002156: [Serial Driver/Interface] COM1 does not work with RTS/CTS

0002212: [Tool/Utility] Add USB printer class 0001122: [Display] Display drivers acceleration level is not adjustable via registry entry

0001939: [General] Add RNDIS

0001849: [Touch driver] Include resistor between both touch films into the sample algorithm 0001831: [General] IOCTL_TIMER_DESTROY blocking in some rare situations 0001827: [USB host] Connected USB devices are not detected reliable if device is already pluged in during boot 0001826: [General] Platform name not present in Regsitry under HKLM\Platform 0001825: [Display] When using bootlogo screen is blank for a short time during bootup (although XDI->N) 0001729: [SPI] SPI receive data always is 0xFF 0001632: [Audio] Unmute master volume by default 0001669: [SPI] Implement software SPI driver. 0001665: [Kernel] Adapt Shell Folder einvironment variables compatibel to PicoCOM2 0001666: [DIO] DIO_REQUEST_IRQ should not fail even when the IRQ has already been initialized to be compatible to PicoCOM2 0001673: [DIO] Change unit of regsitry value "SoftIRQRate" to us (was ms)

0001627: [Tool/Utility] Update to latest NDCUCFG version (V55) 0001626: [Display] contrast +/contrast - give different results compared to contrast set. 0001591: [DIO] Add DIO interrupt support for all pins (Software-IRQ) 0001623: [PWM] Timer driver (TIM1:) restricted to timer controller 0 0001586: [DIO] Difference between driver registry configuration and SW documentation concerning IO43/44. 0001565: [NI2C] Enable option to enable internal pull-ups 0001531: [I2C] Only one instance of (software) I2C driver possible yet. 0001529: [I2C] Implement (software) I2C driver. 0001528: [General] Implement timer driver 0001417: [Serial Driver/Interface] COM1: is not accessable from applications after disable "ndcucfg" and debug output

0001387: [DIO] J1.69 (IO46) is not useable as DIO 0001352: [Kernel] Kernel access to BINFS-Partition broken 0001395: [Tool/Utility] Add NDCUCFG Version V054

0001244: [Tool/Utility] Add NDCUCFG Version V053 0001268: [USB host] Increase PhysicalPageSize default value 0001156: [CAN] CAN driver is not available. 0001128: [Kernel] Add SSHD Server and SMTP Client.

0001118: [Display] Clear display when boot screen with display initialization is used 0001097: [NSPI] NSPI mode changes if clock is >= 1000kHz

0001099: [Tool/Utility] Add Bluetooth PAN features 0001062: [Tool/Utility] Add NDCUCFG version V050 which is based on separate ndcucfg_lib. 0001083: [CAN] CAN not working because DirectInterface option is not enabled by default.

0001011: [Kernel] Bootloader command "R" does not delete HKEY_CU 0001003: [Touch driver] Add EDT Touch Driver to Kernel 0001006: [CEDDK] Update CEDDK library 0000963: [USB device] MassStorage detecting 0000540: [Kernel] Create multi-XIP image

0000903: [USB device] Set USB serial class driver as default client driver 0000899: [USB host] Add custom USB-HID driver version that is able to operate with absolut positioning, which is required for USB-touch modules. 0000912: [Display] Add display mode for ET057090DH to default modes. 0000913: [DIO] IO40 and IO41 are swapped. 0000888: [Display] Disable HW acceleration completly in 8Bpp mode

0000858: [Display] Support for 8 Bpp not working properly 0000866: [NAND-FMD] FAL ignores Read-Only flag, therefore writing access to MBR block must be rejected in partition driver already. 0000851: [NSPI] Chip Select stays low after asserting once.

0000835: [Display] Add support for 8 BPP. 0000837: [Kernel] Add all QFEs until 2011M09 0000836: [OAL] Add support for 128MB RAM 0000644: [CAN] Prepare CAN and SPI driver to work on HW revision 1.20 simultaniously

0000798: [Touch driver] AutoCalib funtionality not working. 0000808: [CEDDK] Improve hardware register access in CEDDK library 0000824: [Display] Allow increasing framebuffer size, even when bootscreen is used. 0000821: [Display] VCFL pin not controlled correctly. 0000801: [Ethernet] NDIS driver hangs if not ethernet controllers is populated on module. 0000711: [Display] Add support for 2D config utility which offers dynamic configuration of acceleration.

0000716: [Touch driver] Update default touch driver calibration. 0000625: [Serial Driver/Interface] Enable support for 3rd COM interface 0000529: [F3S] Add F3S support 0000556: [USB host] USB device will not be detected if already inserted during before bootup. 0000762: [Tool/Utility] Update to latest NDCUCFG version (V045) 0000726: [Display] Exception in CEDDK when using bootscreen and display initialization is disabled in WinCE.

0000692: [SD/MMC] SD Memory cards not detected correctly 0000674: [USB host] Add custom usb disk driver 0000669: [Kernel] Add NTLM support in kernel 0000675: [Display] Update to latest lcd common library. 0000709: [PM ScreenSaver Driver] Add F&S screen saver 0000710: [Kernel] Remove power manager debug messages 0000665: [Display] MSignal option still ignored in case of enabled bootscreen option. 0000648: [Display] Option to disable/enable display "m-signal" not working. 0000650: [Touch driver] Add capacitive touch panel driver for I2C stamp module.

0000626: [DIO] Add supprt for EINT1 0000600: [Kernel] Create new kernel variants: CF2 and CF2_RTC 0000635: [Kernel] Add DDI_NOP driver 0000557: [SPI] SPI driver not available yet (will not be included in a default kernel image). 0000613: [DIO] Port num 12 to 17 are not working       0000612: [CEDDK] DIO pin table must be modified for board rev 1.10 0000544: [Kernel] Keyboard driver missing       0000614: [Matrix keyboard] Add matrix keyboard driver

0000528: [Tool/Utility] Add new control panel applet FSBoardConfig 0000525: [Kernel] Add all QFEs until 2011M02 0000446: [Display] Create generic method to modify power on sequencing 0000497: [Display] Add support for "ContrastFreq" registry value 0000510: [Kernel] Add FTP server 0000511: [Display] Update and unify default display modes 0000504: [Tool/Utility] Update to BCSend version 1.1 0000502: [Kernel] Add Wireless LAN support 0000473: [Ethernet] Modify registry settings to keep it common with other boards using this phy (PicoMOD6) 0000498: [Kernel] Update to CheckAutoStart version 1.5 0000441: [DIO] Add Digital/IO driver. 0000445: [SD/MMC] Add support for SD/MMC cards. 0000493: [Kernel] sysgen_printing feature not enabled 0000475: [Kernel] Inherit current display settings from EBoot.

0000482: [Kernel] First pre-release kernel